Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
When I added to AP to the WLC i checked AP Mode Bridge. I recieve the following error message "Please change the 80211a channel and TxPower assignment method from GLOBAL to CUSTOMwireless->Access points->Radios->802.11a/n->Configure" I am able ...
I would like to use a Cisco AP1262 in a mobile command vehicle to bridge to any WiFi Access Point that I know the SSID and Pasword to. Will the 1262 Bridge to a Non-Cisco Access Point?If so, any assistance in finding an example configuration would b...
Dear all,I bought a power supply for the CISCO 1552E's to make sure both radios are up and running. But when i plug in the power with POE removed, the AP seems to not power up. No signs of power at all. Is there anything else I must do apart from plu...
Only need ask a simple question . What kind of log ( logging level -facillity type )need activate for analyze (I need see all related mac-timestamp-login without radius only secuity filter with mac address ) data into a wireless cisco router 1241
Hello I am troubleshooting reports of poor connectivity with some Access point. I discovered most of the AP's have a Global power level of (5).I think increasing this to 3 would provide enough without providing too much. I also see where the RF param...
Resolved! Cisco ISE authentications failure
Hi, I'm new to wireless and was wondering if we can know on wich AP a client is trying to connect.Here's the problem, a user is getting locked in AD because a device keeps trying to connect to the corporate wireless with a bad password. The only info...
Hello,I'm using one Virtual Wireless Lan Controller and one SSID configured.I enabled the WLAN but it isn't working with the ROOT AP and MESH AP.I configured the ROOT AP and MESH AP and they are with the radios UP and i can access the MESH AP.I enabl...
Resolved! Enable Band Select 5760
Hi everyone... i have a 5760 with 3.3.02 XE ver and i have trouble to connect a several laptops to 802.11n standar with 40mghz channel width most of them go to 802.11a only or 802.11 on 2.4ghz.i have a macbook pro mid 2012 and i can't connect to a 5...
Hi dear friends!!! During the operation of Cisco virtual wireless controller I founded one problem.Our company bought a license 2 months ago, we installed it, and everything was perfect.After last rebooting vWLC from Commands-Reboot and saving chang...
Hi All, I am facing a weird kind of situation. At one of my client side, we have Cisco AIR-2602E APs with ANT-2566 patch antennas. At one IDF, where Cisco 2960X are installed, the APs are not powering up when Antenna is attached. Once the Antenna is ...
Hello experts, I have problem when I want to update images for WLC,============================================================ Boot Loader Menu============================================================ 1. Run primary image (Bad image type) - Activ...
I have a 5508 controller and about 30 AIR-CAP3502I-A-K9 access points across 30 offices in the USA. We have a new UK office and purchased an AP locally to avoid shipping from the US, the UK AP is an AIR-CAP3502I-E-K9. When I try to add the UK count...
Resolved! Enable traffic only during office hours
hi, is there a way to allow traffic on wireless network only during network hours ? i did not seen this feature in our controllers, is there any other way to disable the wireless network after office hours and schedule to get it enable next day befor...
Hello,I am using Airmagnet Planner to deploy new access points on a floor. It is going to a voice grade deployment. I was wondering what my transmit power should be for the access points I will be deploying in this planner. I will be going with a ...
My PI is version 2.0.0.0.294 and the WLC is 7.4.110.0. I recently upgraded my WLC to add a HA controller. Prior to this upgrade my PI had no issues syncing with the WLC. Since the upgrade I am not able to sync with the controller. I deleted and re-ad...
