Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi everybody,I'm trying to configure Cisco 4402 series wireless lan controller on a proof of concept lab, but it's generating extremely high LAN utilization (around 600-700 Mbps) on its connected port to backbone switch. We are using GLC-T on 4402's ...
Hi everybody,We are trying to authenticate wireless clients using radius server and 802.1x protocol. Client wireless interface status remains "Validating Idenitity" and IAS server giving the following error :An Access-Request message was received fro...
Hello, Can anyone help me with the exact roaming values of a Cisco 7925 phone?The phones are connected via a wlc from Alcatel.The phones are changing ap’s constantly even staying on one spot.Do to the roaming there are gaps in the call.Now the Alcate...
Resolved! WCS Licensing - Adding AP Capacity
Hello,We have added some AP capacity to our network and are over our license limit for WCS. We originally purchased:WCS-STANDARD-K9WCS-PLUS-100Our reseller quoted me a jaw-dropping price for WCS-PLUS-50 which seems to me must include the base softwa...
Is it possible to configure such device to act as an access point for wireless lan?regards
When I am in the security section.I select an SSID, I tell it to disable wireless isolation for both within and between SSIDs.After a while the settings reset themselves for both my SSIDs.WAP4410N updated to newest firmware.PID VID: WAP4410N-A V02 So...
Hi Experts,Do you know is it possible to configure WLC and WCS management user access to authenticate to TACACs like IOS routers does.If its possible do you know where I can find a doco as a guide. Tried to find but to no avail.WLCModel No. AIR-WLC21...
After setting up MSE and WCS, I cannot successfully open a http or https session to the MSE. I get a error 404 when I try to connect to any GUI based service for example http://<mse ip>/localadminWhen I check MSE status I see Legacy HTTP: False HTTPS...
I have install the Cisco 1131 ap with acs 5.0I have configured AP with WPA with Radius AuthenticationableAll Windows 7 & XP user connectedMAC user is not connectedthere are two option wpa enterprise & wpa2 enterprise
Hello. I need to replace a static WEP encryption between two bridge with a more secure solution.I'm working with a point to point connection using Aironet 1310 with 12.3.Many thanks for help.RegardsAndrea
HiFor some reason our AP's are no linger broadcasting their names. I can't remeber where to enable this from on the wcs. Anyone jog my memory?cheersCraig
Resolved! Cisco AIR-ANT2506 Compatibility
Hi, I need an omni antenna with the specifications of AIR-ANT2506 for a Lighweight AP 1242 for outdoor installation. The AP is compatible with the antenna, but the description of the antenna says that it is a 2.4 GHz Bridge Antenna. Does this mean ...
I have a 5508 with sw 7.0.98, i have 30 3500 ap conected inn local mode. When we connect a 1142ap on a remote location the radio connect the controller download sw stay there for about 40-90 sec, the reconect. On a other remote site against the same ...
we just purchased a new Cisco Aironet 1142N and it does get hot towards the top center where the Cisco logo is.Is this normal? Should I be concerned?
I have a UC520, two ESW-500 switches and 26 SPA502G phones. Half of the phones are in one building and the other half are in an adjascent building that is connected with a Aironet 1310 Bridge. The bridge is set on the side with the UC520 and one ESW ...
