Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
In my understanding starting from WLC release 5.x there is no specific mesh firmware, instead there is a single firmare train and cisco introduced licensing in order to activate mesh features.Now, if I have a WLC with 4.xM release I want to upgrade t...
Hi,Have just installed WCS 6.0.132.0 as part of a new installation.Have defined my buildings and loaded floor plans (PNG) however every time I try and use the Map Editor it just hangs at "Loading(%) 0%" and nothing happens.Have ensured flash is insta...
I need to design a solution with wireless camera with ISR router, could please some point me the cisco available wireless camera and with 2811 ISR router.
Hi,how can I configure 2 SSID broadcast in single AP 1242 so I can through it onmy PC Windows in wi-fi network proprieties ?In fact I configured 2 Vlan wi-fi onmy network infrastrucure. best regardsLorenzo
hiI have 2 WiSM running in virtualization mode, the AP are not able join, knowing that i am running DHCP locally on the core switch and there is no DNS server, when I checked the boot of the access point it is saying it is unable to receive vci code ...
I need to setup a guest wlan on a single 5508 controller. Currently all of my ap's are in h-reap mode and all in remote buildings connected via a high speed wireless wan.The guest network could consist of 500 users in the near future, so i'm wonderin...
Can someone point me to documentation which shows how to setup a 1252 "A" radio for backhauling to another 1252?
Hi allWe're having a wird problem with voice quality on 7925G phones.They are reg. on a CME 7.0 and running 1.3.3 firmware and at 5Ghz.AP is 1242( 2 of them) and 7 phones(all 7925G).Running QOS , used the deployment guide for 7921G , WDS and eap-fast...
We have a deployment with Cisco 1142 access points mixed with Cisco 1130 access points. I've completed a survey (pre and post install) and tweaked the channel power settings manually because the auto power was setting the AP's way off and causing too...
WLC 2125 (running 5.2.193.0) - Trying to determine if it is possible to have a Guest SSID hand out an address from the internal DHCP server and have that NAT'd out a physically separate interface that just goes to a local ISP? Or is the only way to c...
Hi board,I have a tiny understanding problem regarding client-associations in 802.11.If a client associates to an AP, the AP adds the client to it's association table. How does the standalone AP or the WLAN controller determine the IP-address of the ...
We have a building that is built like a concrete fortress and the wireless coverage internally doesn't work well. This is basically a 5 floor apartment building and we can only have AP's in the hallways. I surveyed with 1142 access points and directl...
We are using 7921 phones over our wireless network with A, B and G APs. The phone is set to Auto-A and the APs are broadcasting the SSID over A and G bands. We are seeing the phones pick the G band 90% of the time. We restricted the SSID to the A rad...
Hello,When I'm running reports in wcs we have a lot of our new machines show as unknown in the vendor list. Is there a way to make manual entries for certain oui's? Or even better, a way to update the list?Thanks,Dan.
We installed a NM-AIR-WLC6-K9 into our 2851 and it is showing "Unknown".Below is our IOS Version and the message.Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(21a), RELEASE SOFTWARE (fc1)ROM: System Bootstrap, Version 12...
