Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I've been trying to figure out what Trusted AP Policies and their respective sub-options might be for. Unfortunately, this subject seems to be documented very badly...Can somebody tell me more about it? Does anybody have some of these features activa...
What is the corolation between the BVI interface and the native vlan. I have a bridge that is connected via a trunk port to an 871 router. The router has a couple vlans configured. On the bridge, I have an ip address on BVI1 that is apart of the V...
Hi Guys,We had iinstalled around 4 Cisco Aironet 1232 AG-SK9 that we had convereted to Lightweight WAPs and installed a Cisco Wireless LAN Controller 4402.We had seen that 802.11a is woeking fine in terms of Signal strength, however using 802.11 g gi...
Pardon my ignorance, but I have never worked with an Aironet 1100. The device I encountered is active and connected to an internal network. My objective is to keep the ssid and password the same but relocate to a different site that is connected ou...
I manage both AP 1000 and 1200 series aironet. I want to believe that the smaller the range (coverage) the higher the speed. I can i control the coverage range of each access point. Is it possible to contain it, it is going way out of the range we wa...
HiJust trying to get a P2P WLAN bridge working and on the non-root I get the error %dot11-4-cant-assocand I do not know why.What do I really need configured (SSID? MAC Address etc) for a bridge to non-root bridge constallation to work ?Just now there...
Hi Guys,I'm looking for some insight on the procedures to connect 2 separate networks using 1300 series bridges. The networks are approx 2 kilometers apart and we have line of sight.I have previously connected between sites that were only a few hundr...
Hello,I have two back to back 1242AG Access Points seperated by about 100ft using the A-Band. One is configured as root bridge and the other is a non-root bridge. We are using 128bit WEP encryption with broadcast key rotation. The APs are connected t...
I have upgraded a 1220 to the G upgrade kit as well as the A. I have uploaded the 12.2.11 code to the unit and it reboots, loads the code, intiliazes the fastethernet then loads the code again and is stuck in that loop. Any ideas?
How to configure for peap in AP 1100 through CLI
I am running a VPN over a pair of 1410's and experiencing less than stellar performance ~ about 2Mb/sec. The radios are operating at 54Mb/sec, the signal strength is -32 dBm, the signal to noise is 59dBm, the Ethernet side is running clean.The only e...
Hi guys,I'm pulling my hair out. I think it something simple but I cant figure out why my access-list is not working.Here's the test access-liststatic (inside,outside) x.x.x.x 172.16.124.15 netmask 255.255.255.255access-list inbound_outbound extende...
I'd like some help understanding an aspect of firewalling. I have CBAC configured on an ISR. The WAN (outside) interface is configured with an ACL that will not allow traffic to come in. CBAC's job is to allow temporary openings in this ACL for co...
Hey There Folks,I have a 3845 router with an AP HWIC installed. The module doesn't seem to transmit any signal. I'm not picking up a thing. Below is what I have configured. I made it real basic; nothing fancy like my 1200 series AP's have on them...
We are using PEAP with ACS/AD as the external Database. The issue or behavior that we are experiencing is that clients require a Cached AD Token for the user authenticate against for the first time. The Client does not get an IP until authenticated ...
