Wireless

I have a simple wireless LAN,no ACS involved.I will like to do simple user authentication on all the wireless users which would like to associate with the A.P,can it be done as I understand the LEAP will able to make the A.P as the local authenticato...

Need expert advise on this setup:6 Buildings to be connected via wireless using350 bridges on a Point-to-Multipoint configuration.Will be running IP Telephony between buildings usinga 2600 router with Call manager express and ATA-186s.For sure this w...

If business that had a couple of AP-1100-802.11-b&g configured according to ETSI, limited in power.......has moved to a new location that is outside that power regulation, how can AP 1100 be reused but with full power cause power is not so strictly l...

Hello,I'm attemping to authenticate from Windows XP to a 3rd party radius server via EAP. I'm debugging the radius server and it seems that the access point is not communicating with it at all. Below is some debugging information from the access poin...

I recently upgraded a 1220 IOS 12.2(13)JA3 and found that the web admin account created by the old Non-IOS web interface is still accessible through the web logon. But the account itself is no where to be found in either IOS config file or Web admin....

Hello,I am looking for the simplest configuration on an AP without any vlan or sub-interfaces configuration. Really the basic configuration for an AP with :- 1 IP adresse- 1 Netmask- 1 Default GatewayThx for any help.

I tring to get the card to come up during bootup. The linksys works this way, but Cisco cards wait for the user to logon before activating the card.

The CB21AG card ships with Aironet Desktop Utility (ADU) - does this software currently have similar software tools as Cisco's ACU. To be specific, does it have a "Site Survey Utility" and/or "Link Status Meter"? If not now, when will we see these fe...

With the ACU installed, I was able to get PEAP working on my 350 card and my 1100 AP. Without the ACU, I just can't get it to work. I the Dynamic VLAN assignment works ok, but I can't get an IP address or pass traffic with a static IP. Has anyone got...

Hello.I've just found these forums and I must say how good it is to find such a good source of information. I'm having a little problem with setting up a Home Wireless LAN and I would appreciate some help. I recently bought a AP350 from eBay and I'm ...

I am trying to get the DHCP server on the AP 1100 working, my question is: Can i also push out a Gateway IP and a DNS server ip with the pool that i can create on the AP?? Do I have to do all of this through IOS or is there a way to do it through the...

I suspect my problem is one due to some trees growing taller this spring and such but I figured I would post a message here to see if anyone had any other ideas.I have two BR350's about 2 miles apart using a Cisco Parabolic dish... the bridges have w...

I have a Cisco 4506 linked to 3 3550 switches. The 3550s run 14 Cisco 1200 APs. The mobile devices are Symbol RF barcode scanners. On the 4506, I get log messages like this:May 31 11:17:03: %C4K_EBM-4-HOSTFLAPPING: Host 00:A0:F8:61:0F:EA in vlan 28 i...

I am using a VPN3005 to secure wireless traffic.Using the public interface for the wireless traffic, I can pass DHCP through to get a wireless address and create the VPN tunnel and use 3DES encryption.My problem is that on the 3005, the default route...

HiCould anyone point me towards a good doc on how to configure an AP1100 to do EAP-TLS auth. using Windows Server 2003 as the Certificate Server and using Windows IAS 2003 as the RADIUS backend? I've found a doc "EAP-TLS Deployment Guide...." but it ...