Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi,I rolled out the latest VxWorks FW (12.04) to our 6 APs and the change is reflected in the header of the user interface. However, when you go to the FW update page where it shows you what version you are currently running, it shows the old version...

In an environment were 2.4 GHz access points are installed, will the WLSE be able to detect a rogue 5 GHz access point on the network? If it does not detect the 5 GHz access point, isn't this a security hole as it relates to the capabilities of the W...

robertlopez by • Community Member
  • 896 Views
  • 2 replies
  • 0 Helpful votes

We're attempting to upgrade the firmware on a series of 350 Wireless Bridges from 12.02 to 12.04.However, we're having difficulties upgradeing the non-root bridge on some of the links.Firmware seems to install OK, but the bridge needs a manual power ...

dgj by • Community Member
  • 528 Views
  • 1 replies
  • 0 Helpful votes

Hi Does anybody know what the reccomended user/ap ratio is?In one site we will be implementing 802.11a at 54Mb/s and in another site we will be implementing 802.11g at 54Mb/s.Thanks.Martin.

m-briody by • Community Member
  • 1997 Views
  • 4 replies
  • 0 Helpful votes

Hello,I have the following situation:- Cisco AP1121G (with IOS 12.2(13)JA1) that connects in the wired side to a HP Procurve switch 2524.- 3 VLANs: Management (20), Staff (100) and Guest (102)- 1 PC connected to the wired network- Wireless users that...

ngr by • Community Member
  • 775 Views
  • 1 replies
  • 0 Helpful votes

Hi There,I think I can use TKIP+WEP without EAP or LEAP, under WEP Encryption there is a box Enable Per Packet Keying. I think this is TKIP but I'm not sure, Is it?If so is PPK original TKIP or CKIP, because as far as I know TKIP should change keys e...

gilmo by • Level 2
  • 683 Views
  • 1 replies
  • 0 Helpful votes

With LEAP, a session key is used. Cisco docs point out, that after the authentication phase, the session key is distributed from the RADIUS Server to the AP and Client.Does this mean, that the session key is transmitted in cleartext?I would be very h...

reinke by • Level 3
  • 1212 Views
  • 1 replies
  • 0 Helpful votes

Hello,Has anyone tried using the WLSE Security Policies? There is no information in the WLSE User Guide as to what configs they check. The Policies are checked via SNMP. By doing a tcpdump of the WLSE traffic I've managed to figure out which OIDs the...

s.vautour by • Level 2
  • 975 Views
  • 3 replies
  • 0 Helpful votes

I have a 350 bridge and am trying to utilize it to connect a site with their wireless ISP. The ISP has given me one IP address and I wanted to place that on the Radio side of the bridge and a private network on the ehternet side of the bridge and be ...

rfulgram by • Community Member
  • 850 Views
  • 1 replies
  • 0 Helpful votes

We have just installed 2 350 Bridges about 150 yards apart. We are experiencing some throughput issues. The thing that bothers me, if I ping the bridge that is plugged into the wired side from a PC that is plugged into the wired side, I see a large f...

c-wilkins by • Community Member
  • 532 Views
  • 1 replies
  • 0 Helpful votes

helloWhen i order a 1100 AP with this ref: (AIR-AP1121G-E-K9), do i need to order the power supply (AIR-PWR-A=) supparently ? or is it shipped automatically with the AP?

Hi, We have a setup of around 15 Nos of AP1200 running IOS 12.01T1,with 802.1x - PEAP enabled. The problem we are facing is when we do some changes in configuration like adding a new vlan on one AP and try distributing the configuration using the Dis...

jagadishs by • Level 1
  • 1019 Views
  • 4 replies
  • 0 Helpful votes

We have several 1100 series access points with multiple ssid/vlans configured on each. We have not been able to get any of our clients to connect to a non-broadcast ssid regardless of the security settings, as soon as we change that ssid to broadcast...

rfrost by • Community Member
  • 798 Views
  • 2 replies
  • 0 Helpful votes