Resolved! Upgrade CISCO AP
Hello All What is the best way to upgrade CISCO WLC AP's when i have no HA only one WLC ? Thank you
Forum Posts
Please help.My client wants to test their new product with wireless authentication 802.1x EAP TTLS. They have CISCO WLC 2504. Can you please confirm if CISCO WLC 2500 support EAP TTLS, if yes then how to configure.So far I have added Radius TTLS serv...
I am trying to do a factory reset of a 1552E via the gui to re set it up for MESH I click on Clear All Config, the AP reboots and all the settings are still there... Any idea why it doesn't actually erase all the config? Is there another way? Thank y...
I can't connect the AP via console, I've already done a default reset via button mode but to no avail.I'm connected via Put I see the boot output but it doesn't appear pronpote (ap: or AP.>) configuration, it keeps emitting the message (waiting for u...
Resolved! 5508 FUS upgrade
Hello all,I need some clarification about FUS upgrade, is it necessary in my case or not. We have Cisco 5508 WLC with old version 7.6.120.0, it is working fine for us, but finally it is time to replace some old AP's with 1850 and 2800 series. I want ...
Resolved! Aironet 600
Hi Scott fella was very helpful and told me I needed to get a WLC possibly a 2504check about but from my point of view prices are a quite high.so would the Aironet work with any make of WLC or does it have to be a Cisco one thanks again for your time...
Hi all, I'm looking for a bit of advice - I have a single Cisco 9130AXI access point at home which I have set-up according the the best practices analyser. The question I have, being a single access point in the whole environment, is there anything I...
I can see in Prime ver 3.7 that clients can be removed from access points in a manual process. Can this be an automated process? Even better if it can target a certain group of MAC addresses to remove? Remove Network Clients From Prime Infrastructure...
Resolved! RAP-to-MAP link speed
Hi i have two 1542 access point running 5ghz in mesh, i just want to find out what will be the max through put i would get between the Rap and Map. currently they only connect to each other via one 5ghz channel as that is the only option i see. than...
Hello All,Just want to know if i can upgarde My cisco's AP AIR-AP2802I-E-K9 from 8.3.132.0 to 8.10.171.0 ? without an upgrade for my WLC version ( 8.3.132.0 ) ? Thank you
Hi There, I have followed all the simple steps to bring up a MAP, but I can't see to get it to connect.They are 1552e AP's and running 8.3.143 on a 5508 I have added the mac addresses to the AP profile.I have one set in Bridge mode with type root AP,...
Hi,I have 2 x 8450 controllers. IOS verion of both is 8.5.151.0 and they are on a different subnets. One in Europe and one in US with no mobility group created between them.I'm on site A where a few APs are associated with WLC in US and few APs are a...
Hello team, We are trying to configure an Access Point 9115 as an Embedded Wireless Controller (EWC) But when we try to download the firmware for WC, we are not able to complete the download via TFTP > Firmware: C9800-AP-universalk9.17.06.01 Follow t...
Hi, We have stumbled upon an issue with the Cisco 2602 Access Points. In the last 3 days APs started to seemingly randomly lose connection to the WLC and are unable to join the Controller again. As of now, about 15 of our 300 APs had the problem. The...
Hi Team, We have Mesh AP (IW6300) having it's association too distant from RAP (IW6300). The MAP automatically reboots after sometime. Is it because there's sufficient distance with it's Parent RAP that causes this issue. or what can be another issue...
