Hello all,I work at a school district, and at one campus we have a 3650 acting as awireless lan controller with 2702i access points. I've been contacted byseveral teachers that are telling me that when the students are watchingvideos on their Chromeb...
Forum Posts
Setup/background: 2504 WLC: 3 interfaces connected, 2 in use, three 2700 AP. Interface 1 on WLC is management and as well used for WLAN P700. Here is the switch port config connecting to port 1 interface GigabitEthernet1/0/9 switchport access vla...
Hi All, I'm trying to connected an 1831 AP to an eval version of vWLC 8.x (I've tried multiple) and keep getting this error:No more AP manager addresses remain..[*12/15/2020 16:02:01.8307] No more AP manager addresses remain..[*12/15/2020 16:02:01.83...
Hi, I've a got a Cisco 870 Router, I insert my ipconfig information. I've a personal computer connected with network cable, but it's impossibile to connect other devices with wi-fi.I can't access to my gateway 192.168.1.1 I've tried to reset the r...
Hi all, please can you help me?i have a AP1852e, originally it was a lightwave ap (capwap) the model finish with K9, I converted it in ME correctly, ( show version command displayed me the rows: AP IMAGE TYPE: MOBILITY EXPRESS IMAGEAP CONFIGURATION:...
HiI have a wlc 9800-cl. I can not reach the gw of ther interface management. Is this possible the wlc only see by cdp the interface ha. Example: show cdp neighInterface gi3 (HA) ----- SWCore I need to create a default route for wireless management?Th...
Hi everyone, I am looking for a command on a 9800 WLC running 16.12(1r) code to see if there are crashlogs, or a core dump present on the system. On my 5500's running 8.5 I have the command 'show core summary'but this is not a valid command in the co...
We have a cisco wireless network on our campus. Recently, a department bought a pair of Sonos speakers to put on the wifi wanting to use the app to push music through.The pairing of the speakers and APP would not work. After a long time with support ...
Resolved! Pass-Through Port on the 1815w Purpose
Hi - Since I haven't found anything that has been able to paint a good enough picture for me by googling I'm hoping someone can give me a real world example showing the purpose of the pass-through port on the bottom of the 1815w as well as the back. ...
Hi,We have the WLC models 3504, 5508, 7510, 2500 models of Cisco WLC in our network.Currently the WLC is running on 8.5.140.0 and few on 8.0 version and few on 8.3. We are looking for a recommended software release that they can be upgraded toCan you...
HiI'm trying to set up my two C9800-L-F controllers with redundancy using RMI+RP, but I find the use of IP addresses confusing. I have given each box 2 IP addresses so far:Management:Controller1:interface GigabitEthernet0vrf forwarding Mgmt-intfip ad...
Bonjour, Les points d'accès Cisco Catalyst 9xxx peuvent-elles uniquement fonctionner en 802.3af? Si oui, sous quelles conditions? > Fiche technique Cisco Catalyseur 9100 Exigences de puissance d'entrée:● 802.3at Power over Ethernet Plus (PoE +), C...
Resolved! Client debug - connecting issue
Hi all,I ran into a problem with one of our sites. Corporate clients are using 802.1x for authentication. Problem is that clients can't connect on wifi. I first thought that problem is with DHCP and not getting IP address, but it might be authenticat...
Hi Team,, Actually I have a query about below one point in WLC HA-•" A Redundancy VLAN should be a Layer 2 VLAN dedicated for the HA Pairing process. It shouldnot be spanned across networks and should not have any Layer 3 SVI interface. No data VLANs...
What's the process to do a factory rest on a 9120 AP via CLI? I'm not finding any commands that work on this model. It is running 17.3.2a code.
