Cisco Mobility Express change MGMT vlan

[beconnect]

Hi All We need to change the default managment vlan on a deployment of 1832i and 1852i For now i only have a 1852 connected and all vlans are configured Van 1 mgmt Vlan 402 clients I have the switch ports configured as trunk and native is the mgmt vlan ( for now 1) AS soon as I change the MGMT to vlan 400 and change the native on the switch to 400 I can no more see the mgmt of the mobilty express How can I change mgmt vlan to 400, for the scope of the Ap's without loosing mgmt and the scope. Regards PS: attached current configuration

[Sandeep Choudhary]

Paste the output of these command from AP:

show interface  detailed management

Regards

Dont forget to arte helpful posts

[beconnect]

Hi here you have it on attacched gif

[Sandeep Choudhary]

vlan 400 have the the subnet 192.168.0.2 ?

Regards

[beconnect]

Hi. 

Vlan 400 mgmt is 192.168.0.0/24 network

192.168.0.2 is the ip of the mgmt for the mobility

vlan 402 clents is 192.168.2.0/23 network

thanks

[Sandeep Choudhary]

paste the swicth side config old(vlan 1) and new one (vlan 400)

Regards

[beconnect]

Hi.

Don t understand

You want the switch config?

Only change the native vlan on ports to 400.

Regards

[Daniel Ordóñez Flores]

Hi @beconnect 

You need to tag the mgmt interface to vlan 400.

(WLC)>config interface address management <ip_ADDRESS> <MASK> <IP_DEFAULT-GATEWAY>

(WLC)>config interface vlan management 400

(WLC)>save config

Espero que la información haya sido útil y si no tienes más preguntas recuerda cerrar el topic, seleccionando la respuesta como "Respuesta correcta"

**Please rate the answer if this information was useful***

**Por favor si la información fue util marca esta respuesta como correcta**

*Tu reconocimiento nos alienta a seguir participando en los foros *

[beconnect]

Hi Daniel.

Only on cli?

On webgui i don’t see that setting.

Regards

[Daniel Ordóñez Flores]

Hi @beconnect 

Yeap, do it by CLI

[beconnect]

Daniel

Cisco mobility express controller on a 1852i:

Run this command, different from the one that you send me.. ( no sucess, still does mgmt over vlan 1)

(Cisco Controller) >config interface vlan management 400

output of show interface detail management: 

(Cisco Controller) >show interface detailed management

Interface Name................................... management
MAC Address...................................... 70:18:a7:10:21:00
IP Address....................................... 192.168.0.2
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.0.1
IP Address Type.................................. Static
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
Link Local IPv6 Address.......................... fe80::7218:a7ff:fe10:2100/64
STATE ........................................... NONE
Primary IPv6 Address............................. ::/128
STATE ........................................... NONE
Primary IPv6 Gateway............................. ::
Primary IPv6 Gateway Mac Address................. 00:00:00:00:00:00
STATE ........................................... CREATING
VLAN............................................. 400
Quarantine-vlan.................................. 0
Physical Port.................................... 1
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. Unconfigured
Secondary DHCP Server............................ Unconfigured

--More-- or (q)uit
DHCP Option 82................................... Disabled
DHCP Option 82 bridge mode insertion............. Disabled
IPv4 ACL......................................... Unconfigured
IPv6 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled

[naushaid@cisco.com]

Hi,

Mgmt interface being untagged is requirement for AP running Mobility express capability.

Refer it documented as well.

https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-2/b_Mobility_Express_Deployment_guide/b_Mobility_Express_Deployment_guide_chapter_0100.pdf

 If multiple VLANs are being used for client traffic, the switch portshould be configured to trunk the VLANs. Also, note that management traffic is untagged and if a VLAN is being used for management, it should be configured as a native VLAN on the switch port. Example of the switch port is as follows: