cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Community Helping Community

4013
Views
15
Helpful
5
Replies
Highlighted
Beginner

ASR 9010 SNMP detail

Hi Everyone,

This is my first post in this CISCO community, so again HELLO.

Regarding the SNMP traps in ASR 9010 (I use IOS-XR:4.1.2), which trap is used to get notifications when the transceiver power is low or below the threshold, also is there a document which explains what each trap does(in detail)? I have already read the

"Cisco ASR 9000 Series Aggregation Services Router System Management Command Reference, Release 4.1"  which was good but not so informative on the topic of SNMP.

Best Regards

Saikat

Everyone's tags (6)
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

ASR 9010 SNMP detail

Hello Saikat,

The list of supported notifications can be found here "MIB Notification Names in the Cisco ASR 9000 Series Routers"

http://www.cisco.com/en/US/docs/routers/asr9000/mib/guide/asr9kmib3.html#wp1602338

The power should be under CISCO-ENTITY-SENSOR-MIB

Configure "snmp-server traps sensor", then entSensorThresholdNotification  trap should be raised when sensor threshold is crossed.

Regards,

/A

View solution in original post

5 REPLIES 5
Cisco Employee

ASR 9010 SNMP detail

Hello Saikat,

The list of supported notifications can be found here "MIB Notification Names in the Cisco ASR 9000 Series Routers"

http://www.cisco.com/en/US/docs/routers/asr9000/mib/guide/asr9kmib3.html#wp1602338

The power should be under CISCO-ENTITY-SENSOR-MIB

Configure "snmp-server traps sensor", then entSensorThresholdNotification  trap should be raised when sensor threshold is crossed.

Regards,

/A

View solution in original post

Beginner

ASR 9010 SNMP detail

thank you so much, this document is good.

Beginner

Re: ASR 9010 SNMP detail

Hi,

Is there a way of changing the default threshold value "entSensorThreshold Table"? If so whats the procedure.

Im using XFP-10GER-192IR+ for inter-site connection.

For eg.

The output of  "show controllers te phy"

Thresholds:                    Alarm High                   Warning High                              Warning Low                                        Alarm Low

              Temperature:               83.000                 80.000                                     -10.000                                                -13.000

                  Voltage:           0.000 Volt                   0.000 Volt                                0.000 Volt                                            0.000 Volt

                     Bias:        130.000 mAmps              120.000 mAmps                       20.000 mAmps                                     10.000 mAmps

           Transmit Power:  5.012 mW (7.00 dBm)       2.512 mW (4.00 dBm)              0.339 mW (-4.70 dBm)                          0.170 mW (-7.70

            Receive Power:  1.585 mW (2.00 dBm)       0.794 mW (-1.00 dBm)             0.026 mW (-15.80 dBm)                         0.013 mW (-18.

Will these values be referred by the entity-sensor MIB or the default ones "entSensorThreshold Table"

which are mentioned inside the MIB specification guide will be used?

Thanks in advance.

Best Regards

Saikat

Message was edited by: Saikat Chakraborty

Cisco Employee

Re: ASR 9010 SNMP detail

Hi Saikat,

no, threshold values can not be changed.

Yes, these threshold should be used and I’d expect both all of them to generate a trap.

Regards,

/A

Beginner

Re: ASR 9010 SNMP detail

thanks....

CreatePlease to create content
Content for Community-Ad
FusionCharts will render here