cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5048
Views
15
Helpful
5
Replies

ASR 9010 SNMP detail

saikchak1
Level 1
Level 1

Hi Everyone,

This is my first post in this CISCO community, so again HELLO.

Regarding the SNMP traps in ASR 9010 (I use IOS-XR:4.1.2), which trap is used to get notifications when the transceiver power is low or below the threshold, also is there a document which explains what each trap does(in detail)? I have already read the

"Cisco ASR 9000 Series Aggregation Services Router System Management Command Reference, Release 4.1"  which was good but not so informative on the topic of SNMP.

Best Regards

Saikat

1 Accepted Solution

Accepted Solutions

Alexei Kiritchenko
Cisco Employee
Cisco Employee

Hello Saikat,

The list of supported notifications can be found here "MIB Notification Names in the Cisco ASR 9000 Series Routers"

http://www.cisco.com/en/US/docs/routers/asr9000/mib/guide/asr9kmib3.html#wp1602338

The power should be under CISCO-ENTITY-SENSOR-MIB

Configure "snmp-server traps sensor", then entSensorThresholdNotification  trap should be raised when sensor threshold is crossed.

Regards,

/A

View solution in original post

5 Replies 5

Alexei Kiritchenko
Cisco Employee
Cisco Employee

Hello Saikat,

The list of supported notifications can be found here "MIB Notification Names in the Cisco ASR 9000 Series Routers"

http://www.cisco.com/en/US/docs/routers/asr9000/mib/guide/asr9kmib3.html#wp1602338

The power should be under CISCO-ENTITY-SENSOR-MIB

Configure "snmp-server traps sensor", then entSensorThresholdNotification  trap should be raised when sensor threshold is crossed.

Regards,

/A

thank you so much, this document is good.

Hi,

Is there a way of changing the default threshold value "entSensorThreshold Table"? If so whats the procedure.

Im using XFP-10GER-192IR+ for inter-site connection.

For eg.

The output of  "show controllers te phy"

Thresholds:                    Alarm High                   Warning High                              Warning Low                                        Alarm Low

              Temperature:               83.000                 80.000                                     -10.000                                                -13.000

                  Voltage:           0.000 Volt                   0.000 Volt                                0.000 Volt                                            0.000 Volt

                     Bias:        130.000 mAmps              120.000 mAmps                       20.000 mAmps                                     10.000 mAmps

           Transmit Power:  5.012 mW (7.00 dBm)       2.512 mW (4.00 dBm)              0.339 mW (-4.70 dBm)                          0.170 mW (-7.70

            Receive Power:  1.585 mW (2.00 dBm)       0.794 mW (-1.00 dBm)             0.026 mW (-15.80 dBm)                         0.013 mW (-18.

Will these values be referred by the entity-sensor MIB or the default ones "entSensorThreshold Table"

which are mentioned inside the MIB specification guide will be used?

Thanks in advance.

Best Regards

Saikat

Message was edited by: Saikat Chakraborty

Hi Saikat,

no, threshold values can not be changed.

Yes, these threshold should be used and I’d expect both all of them to generate a trap.

Regards,

/A

thanks....

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: