DX/SX/MX abd IX Series Endpoint Registration to Control Hub

Hello Everyone, Can we register DX80, SX20, MX800 and IX5000 endpoints on WebEx Control Hub. What will happen with the SX20 Remote and Touch 10 Controller of MX800 and IX5000. 

Change Port Speed for Cisco C9500X-60L4D Switch

Good morning,I have a Cisco Catalyst C9500X-60L4D switch and recently I have been trying to set the speed for a fiber QSFP interface.  Is there another command I should be using outside of the "speed <insert value>"? Auto negotiate does not appear to...

WLC 9800-40 Disable IPv6

Hello  everybody,  sb know, how to disable IPv6 (CLI) on WLC9800-40? SW 17.4.1 IOS-XE Bengaluru. GUI Global Config do not works.  Thanks a lot. 

Bgp AD

Hi I have a doubt if anyone could help me please! Imagine that I have the route 1.1.1.1 and I am receiving this network by iBGP and EBGP with the AS path attribute 200 200 200, the router will choose the IBGP route right?That is my doubt, if iBGP has...

Cisco CT8851 IP Phone firmware replacement

I would like to ask the community for help. I have purchased 40 Cisco CT-8851 devices. I have not used a Cisco phone before. Unfortunately I was sad to find out that I need the CUCM management software. Admittedly, we already have an existing PBX pho...

Automate Start/Stop Isolation on Multiple Endpoints

The Cisco Document Team has posted an article. This document describes how to automate the stop/start isolation on multiple endpoints using the API for Cisco Secure Endpoint. Know of something that needs documenting? Share a ne...

Question about cisco C9130AXI-S configuration

Hello everyone. I have a conference room and it is equipped with a C9130AXI-S. I have searched for the installation instructions so that it can broadcast wifi in my conference room but I can't find it. So I hope everyone can help me with the installa...

Geolocation data not showing after uppgrading FMC to 7.4.2.1

Hello, After upgrading a coupple of FMCs to version 7.4.2.1, we noticed that the "Initiator Country" on the connection events page no longer show any data. We tried to manually update the GeoDB file, but we still not seeing any country information. H...

netflow not working in 9400 in stack virtual

hello everyone. hope you are doing well. i have a question regarding netflow not working on a 9500 catalyst connected to another 9500 via stackwise virtual and for some reason, it's sending 0's when capturing data on wireshark. any help on this matte...

9200和9300，通過管理口進行tacacs認證失敗，找不到原因

如果換成非管理口，tacacs就會認證成功，9200和9300都這樣，不知爲何

TE Agent Unable to get Dynamic IP (DNA Center)

Hallo Community I have succesfully installed TE Agent on 9400 Switch, but the problem is that it is unable to get IP Address from DHCP Server, I also tried to configure Static IP, in both cases it did not work. Without the Agent having IP address, it...

ISE upgrade from 3.2 to 3.3

Hi All,I am planning to upgrade ISE (3.2.0.542) patch none to ISE 3.3 Patch 3. My question is can I directly upgrade from my current version or should I upgrade patch on my current ISE version and then upgrade to 3.3 patch 3.Pls suggest patch version...

source base Application filtring in FMC

as i know in fmc-ftd application control or filtering in policy is work for user --> application however does it work for server<---application. in short my source will be xyz public application and destination is my private server in this scenario f...

Secure Client 5.1.6 - French translation error

StackWise and StackWise Virtual Difference

Hello, I’m new to Cisco and currently studying StackWise and StackWise Virtual. Both technologies seem to reach the same goal for high availability and provide single management interface. I wonder why both exist, especially StackWise is supported in...