Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
Cisco ATA 191 solid orange light reset button not working
by razel0 -
Cisco U labs - copy and paste from instructions to VM?
by -
ACI forwarding question:
by jesteen-wrangler -
PEM 형식의 인증서 가져오기
by Masaki Yamauchi -
导入 PEM 格式证书
by Masaki Yamauchi -
FMC HA SECONDARY NODE IP CHANGE
by ahmedFawzy -
9800-40 HA Upgrade from 17.3.7 to 17.9.7 with Ap 3700
by albertobriceno -
Unable to join Cisco meetings in Macbook
by tarngmyna
Community Activity
Cisco ATA 191 solid orange light reset button not working
Cisco ATA 191 solid orange light reset button not working has anyone found a way to fix this?
Cisco U labs - copy and paste from instructions to VM?
My question is, in Cisco U labs, how does one copy and paste from instructions to the VM?I researched but not found a solution, hence I am here asking for input.Within a Lab within Cisco U training, how can you copy text from the side-bar instruction...
9800-40 HA Upgrade from 17.3.7 to 17.9.7 with Ap 3700
I need urgent help.I have a C9800-40 controller with firmware version ios 17.3.7, with HA SSO. This controller has registered access points models 3700, 3800, and 9120, with external antennas and some with internal antennas.I need to update the firmw...
ACI forwarding question:
ACI forwarding question: usually in a single pod when an endpoint wants to reach with in the same subnet but it dest not known it will send a spine proxy to one of the spines. And Spines check for the endpoint if not present it will drop it won't flo...
PEM 형식의 인증서 가져오기
Secure Email Gateway (SEG)를 사용하면 GUI에서 PKCS # 12 형식의 인증서를 가져올 수 있지만 PEM 형식의 인증서 가져 오기는 CLI에서 수행됩니다. 다음은 PEM 형식의 인증서, 개인 키 및 중간 인증서를 붙여넣고 가져오는 예입니다. esa.example.com > certconfigChoose the operation you want to perform:- CERTIFICATE - Import, Create a ...
导入 PEM 格式证书
Secure Email Gateway (SEG) 允许您通过图形用户界面 (GUI) 导入 PKCS#12 格式的证书，但导入 PEM 格式的证书则需要使用命令行界面 (CLI)。以下示例演示了如何粘贴并导入 PEM 格式的证书、私钥和中间证书。 esa.example.com > certconfigChoose the operation you want to perform:- CERTIFICATE - Import, Create a request, Edit or Remov...
FMC HA SECONDARY NODE IP CHANGE
I'm going to move my secondary FMC device to another physical location and i will change its ip address used in the HA configuration. so, i was planning to 1- break FMC HA 2- change FMC IP 3- configure HA again what i expect that FTD will be manage...
Vlan deployment
I know it's a very silly question to ask, but I want to know whenever we create a vlan with vlan vlan-num e.g. vlan 10and then till we don't use exit and came back to configuration mode the vlan doesn't show up. Like why we have to explicitly 'exit' ...
BLF with 8851-3PCC on Asterisk System
Hi Together, i'm having problems with configuring BLF on 8851 3PCC with Asterik System. BLF are blinking and when pressed i've getting failure "Invalid Number". Software Version: sip88xx.11-0-1MPP-477.loads Voice with no problems, Calls possible ...
Cisco SMA resources allocation
Hello, I already assigned lower specification for virtual cisco SMA on Microsoft hypervisor. i need to assign higher resources for the SMA. what is the best practice steps to this.
Unable to join Cisco meetings in Macbook
For a few weeks now, I have been unable to join Cisco meetings on my work Macbook.Whenever I try to connect I get a message "Unable to join call". People inside the call can see me as "connecting".I don't have an account and everyone in the company c...
Resolved! 9800-40 HA Upgrade from 17.6.4 to 17.9.3
We are upgrading our 9800-40 HA Upgrade from 17.6.4 to 17.9.3. Can these versions be upgraded to directly from and to, or is there version steps?Since this is an HA pair, can these be upgraded one at a time by failing over and upgrading the standby?C...
Cisco anyconnect connects everywhere but refuses to connect to home ne
My work VPN connects everywhere but my house WiFi. It loads for a good minute then says “connection attempts has timed out. Please verify internet connectivity”. At first I thought it was my mesh router. I have orbi RBS850 router with two satellites ...
HWIC-16A Configuration - Hardware fault?
I'm trying to configure a HWIC-16A as a terminal server without success. I can get a telnet session to connect, but I simply get a blank screen, no data appears to be sent or received over the serial line.The only similar post I could find was https:...
Cannot access vmanager on GUI
Vmange(config)# do show running-configsystemhost-name Vmangesystem-ip 1.1.1.1site-id 100admin-tech-on-failureorganization-name airtelclock timezone Asia/Kolkatavbond 100.1.1.3aaaauth-order local radius tacacsusergroup basictask system read writetask ...
