Hi,I have a cisco 9200 switch which is not syncing to NTP server (Linux based). No firewall is in between switch and NTP server Switch is able to ping NTP server IPUsing management vlan, not an vrf Switch9200#sh ntp statusClock is unsynchronized, str...
Forum Posts
Network Diagram briefPlease refer to the attachment or the following for the network diagram Please note it is a lab diagram for learning and testing purposes.-> There are 4 IOS XE Routers-> The interface links are represented in the following form...
The router is RV320, preparing to enable remote access. After setting up DDNS and external network access ports with the RV130 I used before, I could directly access it. However, this model prompts a 502 BAD GATEWAY error. Could someone please guid...
Hi all!I have a couple of questions regarding ospf route redistribution:1. How can I determine which ospf routers are being redistribute into other protocols? First, I thought show ip route would give me the answer, but apparently not. For example,...
I have a Firepower 2130 that homes all of my S2S VPN connections, as well as some AWS Direct Connect and Microsoft ExpressRoute links.The FW has static routes for VPN destinations, to push them over the appropriate outbound interface, and a route-map...
Resolved! Channel group issue
Hello all!I ran into an issue when assigning a channel group to an interface on my C9372PX core switches running EIGRP. I created a port channel on both cores and assigned the channel-group 45 to interface Ethernet1/45 with no issues. When attempti...
Resolved! Remove RIP from interface
Hello I have the following configuration on a subinterface and I what to remove the RIP configuration from it. interface TenGigabitEthernetx/y/z.100 bandwidth 20000encapsulation dot1Q 1234vrf forwarding vrf-nameip address 1.1.1.1 255.255.255.252ip fl...
Our client recently purchased a Network Advantage license to upgrade an existing IE3300 switch from Network Essentials. They need this to enable EIGRP routing functionality. I ran through the license reservation upgrade procedures from the Cisco docu...
Resolved! RV325 502 Bad Gateway
Hi, all,I have an RV325 (yes, I know it's old) and am having a problem.When I first got it I did a factory reset and updated the firmware to V1.5.1.13, which worked ok. I was able to sign on using cisco/cisco and start configuring it.When I tried to...
Hi,I am learning about BGP Path Selection process and precisely about "Oldest Path" criterion. I am using Perplexity to do that and on one question I asked it about this, the AI replied with this sentence:"To illustrate how the Oldest Path criterion ...
Hi team, Please help with c8200L-1N4T router having an issue of not booting C-NIM-8T card It is showing booting since last 1 hour in show platform :card status is booting After this issue, Version upgraded from 17.06.06a to golden image 17.9.5f, but ...
Hi Community Members.,I set up a Failover /Load Balancing on a Cisco Router using Dual ISP and DUAL LAN segmentAs shown below:From the Edge Router: Config.track 1 ip sla 1 reachability!track 2 ip sla 2 reachability!interface FastEthernet0/0ip addres...
Public IP = XXPrivate IP = YI have a weird requirement from cyber that they want double encryption. We currently have a hub and spoke Arch with a specialized equipment that i will call A devices. Cyber wants to put ASA infront of A devices. currently...
Apologies in advance for the crude drawing There's an original setup where the green dmvpn did not exist, R1 is the home office R2/R3 are remote offices with substantial bandwidth to the home office, R4/R5 routed everything to R2/R3 over a GRE tunnel...
Hi,On nexus 9k ver 9.3.5 I am using message digest key to create a type 7 digest, but I am getting this error:Error: Invalid Type 7 passwordThe exact same configuration on version 9.3.1 works fine. So something must have changed in this version but I...
