Hi guys, I have an WAVE-7371-K9 with WAE-INLN-4CG. Is there any way to use both modes inline (in-path) and WCCPv2 Interception at the same time in this appliance ? I think you can use just one mode (in-path or off-path), but I wanna confirm ...
Hi,I am having a issue with WAE-7341, it went offline after clearing the cache on it and reloading it. The WAE is running WAAS OS 4.3.5 . Before the device went offline, I did the below steps.1. cleared the CIFS cache2. cleared the DRE cache3. cleare...
HelloWe have two pairs of ACE 4710s, one pair running A3(2.4) and the other pair A3(2.0). We plan to upgarde the second pair so that they are running the same image as the first pair (we know they are not the latest, but this is the first step in a l...
Hi Gilles,is there a tcp idle timeout with exact 60 minutes within ACE Software for NON LB connections?I have a certain TCP Connection from a FrontendServer to a certain Backend Server which gets a TCP RST every 60 minutes.The application guys blame ...
I have an issue with a wae-512 device were it suddenly becomes unreachable and i'd have to shut/no shut the port connected to it to become reachable again. i have taken the show arp from both it's gateway and the wae device itself. the arp entry for ...
Hi all,ACE20 module with A2(3.3)I have tried to config a NAT-pool with two adresses, but only one is used. class-map match-all NAT015_VLAN702 2 match source-address 192.168.137.93 255.255.255.255 3 match destination-address 192.168.137.0 255.255.25...
Hello, I have a back-end ACE which needs to create a sticky based on a header value. The X-Forwarded-For header is perfect as it indicates the original client ip. There is a front end ACE which is setting the header correctly. My goal is to have ...
I'm currently load balancing a couple FTP servers and the vendor is asking me to make sure to have IP passthrough and no header rewrite. I believe he is looking at a different company LB. What is the Cisco terms for that? Is this something that I nee...
I'm configuring ACE to enable the XML-HTTPS interface so I can import it into ANM, when I try to do a "match protocol xml-https any", I get a invalid command detected. When I tab at the match protocol command, I don't see xml-https listed (http, http...
I am running WAAS Mobile Server 3.5.3 in our test environment and I have clients that are peering with the server but they do not show up in the admin interface on the server. It says that there are no connected clients but the clients clearly show t...
Hi all. I have an ACE context with many bridges configured, for example:Bridge 1 with vlans 10 and 20Bridge 2 with vlans 30 and 40Vlans 10 and 30 connect to clients and vlans 20 and 40 connect to servers.Vlans 10 and 30 are transit vlans betwen a FWS...
Hi all,One of our site have an MPLS as primary line and an 574 toghether with inline card.Now the site needs an backup line, setup with VRRP as shared ip number.The backup device is not an Cisco, and we can’t use WCCP, or HSRP.Should we use the secon...
Is it possible on the CSS11503 to create a layer 5 content rule that matches a url "/*/_edit", so that the following example URLs are matched by the content rule:http://www.example.com/mysite1/subdir1/subdir2/_edithttp://www.example.com/mysite2/subdi...
folksi've inherited a cluster of CSS11501s and i'm never really used them beforecan someone point me in the direction of a good troubleshooting guide please?i'm running CSS11501# sh versVersion: sg0820101 (08.20.1.01)Flash (Locked): ...