Application Networking

Hello,I have the Cisco 7606 with IOS: s72033-adventerprisek9_wan-mz.122-18.SXE2.bin.I try to clear the sticky db with: clear ip slb sticky radius framed.But after few swconds I can see with the sh ip slb sticky radius fra old flow and a lot of entri...

Hi,I want to configure redundant css11503 switch.please let me how to configure redundant on both the switches.How physical connectivity need to be made.Please find the sh ver.CSS11503# sh verVersion: sg0730203 (07.30.2.03)Flash (Locked...

Hi,I have 2 CE507 running in web-caching mode (WCCPv2) with ACNS 5.3.3 software. After installing the new version we discovered this particular error message that keeps popping up:%CE-HTTP-5-270029: handle_http_100_continue(): Invalid request method(...

Hello,I problemed on the ce-560 following:System Initialization Finished.CE-560#show disks ruby_disk: Disk /dev/sdb: cannot open: Device not configuredSYSFS 0.0GB 0.0%CFS 0.0GB 0.0%MEDIAFS 0...

I would like to write a documentabout config restore of an C6K SSL module. Restoring the saved running-config is not enough.Key pairs have to be imported manually. (crypto key import ...).SSL certificates using those keys are included in the running ...

We were running some tests to our https portal using a java script. We were running into some errors. After the errors, we did a "show tech" on both the 6500 switch and the ssl-module.We ran the same test script again, and the errors went away and wa...

Hello,I think I am in the twilight zone right now so if somebody can put me out of my misery please do :-)Here is the situation: I have a pretty straightforward configuration where I load-balance SSL in a very simple way, here is my config:service ss...

Hi,Somebody can explain me the following line.I don't understand how I can to do that. The server 192.168.31.18 don't arrive to connect in smtp to the server 192.168.5.137.Thanks--------------- ----- --------------- ----- --------------- --- ------- ...

Recently we upgrade from 7.3 to 7.5 and the MIBS have changed. This has caused problems monitoring the CCS modules.Where can I find the syslog messages generated by the CSS so that we can monitor via syslog ?cheers,Mike

We just upgraded one of our CSS's to 7.4, now our HSE version 1.8 cannot see it correctly. I am assuming some MIB's got changed, how do I fix this? here is what i see;10.28.3.6 10.28.3.6 CSS 11506 10.28.3.7 10.28.3.7 .1.3.6.1.4.1.9.9.368.4.6 10...

Hi all,we currently have in our network a LoadBalancer that is infront of an SMS application. All inbound connections work fine on a global rule: content Application_SMS vip address 110.10.10.10 add service SRV_a add service SRV_b add service...

I have to chassis configured identically, 1 ea, CSM, SSL Mod. I've created a backend encryption setup using a serverfarm consisting of three "reals". I'm using SSL Sticky for the HTTPS Vserver and I believe it's operating properly, in other words a c...

HiI have a CSS configuration that advertises static outside addresses for several server pools that reside off the inside vlan of the CSS. This works fine.Can I set up a server pool with an inside vip rather than an outside one to allow a server on t...

When you ping a VIP address, is it the CSS that replies or does the CSS forward the ping to one of the servers in the farm ?

Hello,We have a content rule configured (VIP address 10.1.2.3) but have not configured an ip redundant-vip 1 10.1.2.3 under the circuit configuration on either the master or backup CSS.This content rule works though ? Why is this ?cheers,Mike