Collaboration Knowledge Base

Subject: SX20 Quick Set Documentation Replied by: Larry McIntyre on 30-01-2012 10:00:53 PMWhere can I locate information on the SX20 beyond the cut sheet, e.g. Installation or Owner's Manual, I/O drawing, etc?Also, the embedded video on the SX20 web ...

This document was generated from CDN thread Created by: Enrico Conedera on 27-01-2012 06:49:18 PM Yes, you can do that.  This is an excellent example of the integrator capabilities of the C40.  It supports a standard VISCA chain of up to 7 cameras, l...

This document was generated from CDN thread Created by: STEVEN JACK on 27-01-2012 12:19:09 PM Hello, I would like to write an application that allows us to place a CODEC into DUO Video Mode either manually or on a scheduleI anyone has any example cod...

This document was generated from CDN thread Created by: Kari Teffeau on 26-01-2012 06:07:02 PM I recently encountered this issue:When you send a pan/tilt/zoom command to Precision HD camera attached via the camera control port to a C-series codec OFT...

This document was generated from CDN thread Created by: Marcus Newnam on 26-01-2012 04:53:46 PM The HTML based TC5.0 API documentation for Codec C90, C60 + C40 and C20 is in the perfect format for consumption.  http://developer.tandberg.com/docs/api/...

This document was generated from CDN thread Created by: Enrico Conedera on 26-01-2012 03:53:22 PM I tested the Extron DVI 201 some time ago.*********************Power in this test is supplied to the HDMI 201 pair at the transmitter end. I recommend t...

This document was generated from CDN thread Created by: Matt Keenan on 26-01-2012 02:05:00 AM Can anyone advise a quick way to remove the (H323) prefix from Phone Book names where Name entry equals MeetingRoom (H323)?I have setup a TMS Phone Book Sou...

This document was generated from CDN thread Created by: Enrico Conedera on 25-01-2012 11:47:47 PM The manual for the XF100 says that it outputs 480p60, which is most likely sent as 640x480, which is not a true 16:9 format.  If the output format were ...

Subject: C20 RS-232 Standby Control Replied by: Matt Keenan on 25-01-2012 11:10:46 PMHi all,Is it possible to activate Standby Control on a C20 from the Touch Panel over the Camera Control Port to an RS-232 connected device?We have older NEC LCD4020 ...

This document was generated from CDN thread Created by: Enrico Conedera on 24-01-2012 07:50:13 PM Assuming you have the correct pinout on the adapter.  RevoLabs makes one: 07-XLRTO35M4-01        Cable XLR Female to 3.5 Male (4 Conductor) - 3'      $3...

This document was generated from CDN thread Created by: Alexandre Lopez on 23-01-2012 01:14:11 PM When booking a recurrent via Lotus Notes a meeting with rooms that have already been booked, the booking is 100% rejected.If you compare with natural be...

This document was generated from CDN thread Created by: Regan DeDiana on 22-01-2012 01:06:46 AM Hello,is there an API interface to retrieve recording categories from the TCS?thanks

This document was generated from CDN thread Created by: David Bruun-Lie on 20-01-2012 02:41:43 PM Hi Chet,are any of the codecs registered to a gatekeeper (or both on different gatekeepers) where maybe IP dialling is not allowed?Cause Code 6 means:Ca...

This document was generated from CDN thread Created by: joaquim Fernandes on 20-01-2012 10:23:45 AM HI team,I am stuck with one more issue.One of customer is Tanberg CTS-880V35-PAL, which is EO Life and EO sale.However the END of Support is still the...

This document was generated from CDN thread Created by: David Bruun-Lie on 26-03-2012 02:47:58 PM Have you checked with the Crestron Toolbox that the codec is giving a reply to the commands?Done a reboot?Changed password?Maybe someone enabled passwor...