Collaboration Knowledge Base

This document was generated from CDN thread Created by: Bill McNine on 07-01-2010 08:02:44 PM Is it possible to have a 1700MXP send the value of RemoteNumber whenever that value changes using the API's feedback mechanism? I'd like to telnet to the 17...

This document was generated from CDN thread Created by: Andre Garcia on 07-01-2010 12:59:55 AM I've got the demo 1.3 module loaded into my processor, but having problems creating a side by side layout where half is the far end and the other have is t...

This document was generated from CDN thread Created by: PAYAM MOGHADDAM on 02-01-2010 10:24:44 AM Is it possible to trigger a camera preset through RS232 port by connecting an external device, and sending special commands to an MXP codec?ThanksSubjec...

This document was generated from CDN thread Created by: Takumi Kumagai on 28-12-2009 02:55:56 PM Hi!I'm developing a video conference booking system with TMS Booking APIIn TMS_3rd_Party_Booking_API_D1356607.pdf/---------------------------------------...

This document was generated from CDN thread Created by: Henri Brinkhuis on 22-12-2009 05:11:40 PM We are looking at using the 720p PHD cam as a recording camera (i.e. put a recorder directly on the camera) and I've noticed it has a HDMI port. However...

This document was generated from CDN thread Created by: Jeremiah Brown on 21-12-2009 06:14:43 PM I am looking at the 'Tandberg C90 + C60 Serial v1.3' Module, and at the inputs for Picture Layout.They send the 'xCommand Video PictureLayoutSet LayoutFa...

This document was generated from CDN thread Created by: John Faltys on 18-12-2009 02:42:52 AM With the MXP http://xxx.xxx.xxx.xxx/formputxml?xmldoc=<Command><CameraPosition><Camera>1</Camera><Pan>200</Pan><Tilt>200</Tilt></CameraPosition></Command>wo...

This document was generated from CDN thread Created by: John Faltys on 18-12-2009 01:54:01 AM Can someone please tell me what I am doing wrong?If I try to move an MXP, I usehttp://xxx.xxx.xxx.xxx/formputxml?xmldoc=<Command><CameraPosition><Camera>1</...

This document was generated from CDN thread Created by: Cameron Davidson on 17-12-2009 03:49:17 PM Hi I have two systems on two different sites. Site1 has two TC60 Firmware TC2.1.0Site2 has two TC90 Firmware TC2.1.1When using the video input it bounc...

This document was generated from CDN thread Created by: Matthew Taylor on 15-12-2009 04:39:46 AM G'day,I am using an AMX system to control the following.MXP 6000 F6.3 (connected to the AMX serially)TVSTandberg HD camera on DVI Input 1 and control inp...

This document was generated from CDN thread Created by: Donatas Raisutis on 10-12-2009 03:05:04 PM I am plannig to move our 4 TCS to a cluster. I was reading TANDBERG documentation how to do this and it looks ok.I could not understand why it is neede...

This document was generated from CDN thread Created by: Sammy Moore on 10-12-2009 03:24:13 AM C60 firmware 2.1.1Pro2 firmware 4.001.1012module used: "Tandberg C60 + C90 Serial v1.3"I downloaded this module off this site 2 days ago and created a test ...

This document was generated from CDN thread Created by: Donald Newman on 10-12-2009 01:33:14 AM Can an Edge95MXP accept a YPbPr component video signal on it's VGA (HD15) input?Thank-you,Donald NewmanUniversity of GeorgiaSubject: RE: Component video i...

This document was generated from CDN thread Created by: Nelson Perez on 07-12-2009 07:54:57 PM As Lead Telepresence Engineer for Tandberg I've been providing the world with opportunities to lessen their Carbon footprint through the installation of Ta...

This document was generated from CDN thread Created by: chris rawden on 03-12-2009 05:21:04 PM HiAfter ugrading a C 90 to TC 2.1.1 from TC 2.0.0  the AMX panel cannot pick up the phone book.I have looked through the API  and cannot see what has chang...