02-26-2021 12:43 PM
Hi Experts,
I am a bit confused to understand the queue time and the ring time in the CCX.
I have configured the queue overflow as shown below.
Please correct me if I am wrong here;
Am I doing anything wrong here or am I missing anything else to be considered? as long as the queue time is great 12 seconds, i am expecting to see more than one entry in the report or increment value in the Ring No Answer column of CSQ Agent Summary Report.
Highly appreciated any inputs.
Regards,
Shalid
02-28-2021 09:41 AM
Hi Shalid,
Your script looks a little odd. Most scripts would use one Select Resource step rather than four linked one as you show.
You could use Most Skilled to select agents in the way you want.
The reporting would work better as there would only be one CSQ to report on (I am assuming that your four Select Resource steps go to separate CSQs).
02-28-2021 07:17 PM - edited 02-28-2021 07:25 PM
Point 1 is fine.
In Point 2, Queue Time and Ring Time measure different parts of the call..
Queue Time - "Elapsed time between the time a call entered the Contact Service Queue (CSQ) and the time that the call rang."
Ring Time - "Elapsed time between the time that a call rang and the time that the call was answered by an agent, routed to another agent, or disconnected. This field is blank if the call was not routed to an agent."
So don't think they'd be the same as they are measuring two different things.
Also, think you'd see the RNA stat in a different report for the agent that didn't pick up the call, not the agent that eventually answered it.
In the Select Resource Step that 12 is for ring time only - i.e. in the docs it specifies that it has to be less than than UCM disconnect or forward to VM timer. See https://developer.cisco.com/docs/contact-center-express/#!select-resource-step/select-resource-step
If you want to stagger the time before introducing another CSQ you'll typically use prompt/delay.
Wish you all the best.
03-02-2021 07:08 AM - edited 03-02-2021 07:13 AM
I referred to the shared documents mentioned in your response. unfortunately, there are no delay or queue prompts in the script. The client doest like any system interacting with the caller. I got the point related to the Queue time and Ring time. If there are no prompts or delays in the script, do you think the queue time and the ring time should be around the same? I checked the MIVR logs and I didn't see anything which delays the call delivery.
Very often the report shows a very high duration than the ring time and not seeing the call rang in any other agent (not registered RNA for any other agents. I am unable to give a proper response to the requester yet.
The RNA has configured correctly. UCCX RNA < call manager Call Forward No Answer timeout
Regards,
03-02-2021 05:19 PM - edited 03-02-2021 05:29 PM
(a) Test the Queuetime/Ringtime with a test script set up in the same way (no queue prompts) with one CSQ and one agent. Deliver a call, let it ring for a set amount of seconds, answer it and then check the report. For me, they should be different but for reporting stuff like that I always do a little test at the lowest level.
(b) The script itself might be a reason why you don't get an RNA. Basically, the way I read it is that:
(i) Call is offered to CSQ. If agent isn't available in CSQ call is offered to (CSQ + CSQ1). If agent isn't available in (CSQ + CSQ1) then call is offered to (CSQ + CSQ1 + CSQ2). If agent isn't available in (CSQ + CSQ1 + CSQ2) then call is offered to (CSQ + CSQ1 + CSQ2 + CSQ3 ). Call doesn't have to ring at agent phone while going through this logic. See https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-contact-center-express/63710-multi-csqs-call.html
Looking at that script I think it might be possible for call to be queued to ( CSQ + CSQ1 + CSQ2 + CSQ3 ), go to QueueMessage and be answered by an agent in any of those CSQs .
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide