Buy or Renew
Buy or Renew

Controllers

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Developer Sustainability Week Events

Build for Better Code Challenge

Cisco U. Spotlight Registration


>> View previously featured conversations <<

Forum Posts

Start a conversation

Resolved! APIC-EM Backup File

Hey team, Quick question about APIC-EM backup file.Any idea why there's a duplicate of the APIC-EM backup file (in the controller server)?Location #1:/srv/grapevine/replicated-storage/backups/4960085a-9a16-11e7-bbd8-0025b500303f/backup_2017-09-15_13-...

ymeloch by • Cisco Employee
  • 1477 Views
  • 5 replies
  • 2 Helpful votes

Trunk

Hi ALL,Sw(config)#interface GigabitEthernet1/0/25Sw(config-if)#switchport trunk allowed vlan 3,20,30,31,40,42,44,50,60,70,80,110,120,121,130,140Sw(config-if)#switchport mode trunkwhy is it showing like that ?Sw#show run | s GigabitEthernet1/0/25inter...

Resolved! Unable to authenticate via API

Hi all,I'm able to successfully login to the APIC with a particular set of credentials via the GUI, but when I try to login via the API I get "Username or password is incorrect - FAILED local authentication".Below is the request I'm making, along wit...

Resolved! APIC-EM PnP Template Issue with VLANs

I have a template that adds VLANs and VLAN names to switches.  For some reason when the template is pushed it will not create the VLANs on the switch.  When I manually paste the config in, it works fine.  Any suggestions.  Note, two of the VLANs are ...

v1.5.1.1054 upgrade - status 'harvested'

Hi there,I attempted upgrading to v1.5.1.1054 from v1.5.0.1368 early this morning, it initially failed due to NTP sync issues. I resolved these and attempted the upgrade again. After waiting over two hours for it to complete, I refreshed the page and...

Seb Rupik by • VIP Alumni
  • 1618 Views
  • 6 replies
  • 1 Helpful votes

APIC-EM Discovery issue

HelloI have a problem with discovering netwrok devices. Some devices are failed with "CLI validation failed" message. However during next run for this discovery, previously failed devices are discovered proparly and other devices (that have been disc...

Unable to access Https:// of APIC-EM,

We are unable to access the HTTPS link on APIC-EM, Services were running last week & we had unexpected power shutdown,  once after the power restoration, we are unable to access the application via HTTPS. I checked with grape instance status command ...

APIC not discovering some hosts

HiI did read one of the previous posts where EM do not discover wired endpoints.  I did look at the articles and suggestions posted and verified the environment my controller is installed in.I have a slightly different issue here.  This is a multi vr...

Resolved! APIC-EM Activeadvisor - update list

HelloYesterday I added several new devices to our APIC-EM. They are added to inventory and marked as managed. However I can't see it on Activeadvisor app. I noticed, that number of devices in home screen and CAA app screen is different. Should I manu...

APIC-EM PnP Option 43

Greetings all!I'm setting up APIC-EM (version 1.5) and running into a problem with the PnP module(also 1.5). I've set my upstream switch as the dhcp server. My 2960-X switch (running c2960x-universalk9-mz.152-2.E6) is able to get an ip address, and s...

PnP with Switch Stack

Hi Expertswe have a customer who has switch stack (member varies fro 3 4 ...8)We have installed APIC EM and going to use PnP to manage those switches. We are not sure how to make a switch as Master in stack using APIC EM. is there a best practice to ...

Load more
Top Solution Authors
View All