topology: ASA failover active/standbynexus vpc+hsrp vitual ip on sw01(left) NXOS:version 9.3(3)host in vlan 942，in access switchissue: everyhost can ping vlan942 gateway (physical address and virtual address)some hosts can ping SVI 30,some host...
Messages de Forum
when trying to access the APIC, I get the following error: "we could not verify the certificate: reason = untrusted". I exported and installed the certificate, but I'm still getting the same error. Has anyone else run into this?
hello guys, I'm migrating an existing VLAN currently stretched between Site A and Site B over OTV into ACI, with the SVI/gateway also moving to ACI. As part of this migration we have configured, in the stretched template: A shared VRF and a stretche...
I'm trying to perform two operations on an existing vPC port-channel (interface policy type vpc_trunk_host) managed by NDFC, and both appear impossible from the GUI:Remove a member port from an existing vPC port-channel : the interface field is greye...
We have deployed a Cisco EVPN VXLAN Multi-Site fabric consisting of two main sites, each with: 2 Spine switches (Nexus 9364) 2 Anycast Border Gateways (Nexus 93180) multiple Leaf switches (Nexus 93180) In addition, we have a third site composed only ...
Hello,I configured an ACI Multi-Site deployment with a Bridge Domain stretched between Fabric 1 and Fabric 2.From the control-plane perspective, I can see that the spine switches learn all remote IP/MAC entries via BGP EVPN and correctly install them...
Could you please provide the 3D model step file for the IE-3500H-14P2T.
Hi, After completing the whole config and save it with wr, copy running-config startup config when I reboot the switch, the config is not there!! Any clue plz
Hello,I have a wifi acces point connect to a switch C2960X.Often people unplug cable and connect its equipments in place of this wifi acces point !I was considering to configure port-security on this port, but i'm afraid to block all wifi trafic ... ...
Hello,In our datacenters, we have three physical NDFC appliances. Two of them are connected via 10G to 4510R and are working perfectly without any issues.However, due to hardware availability, the third node is connected to a 3750-X switch with a C3...
IOS 16.9.4 runing version on ASR1k %IOSXE-3-PLATFORM: R0/0: cpp_cp: QFP:0.0 Thread:082 TS:00058948579859346288 %IPSEC-3-REPLAY_ERROR: IPSec SA receives anti-replay error, DP Handle 21, src_addr 103.87.15.106, dest_addr 172.20.236.1, SPI 0x686a3887...
Hello,I have a Cisco 9200 where is connected my Cisco Access Point 3800 Series.The Access point is attached normally to the controller Cisco 5520 but the SSIDs are not shown arroudn the Access Point. I think that it is due to the fact that the switch...
Résolu! Route-map on Nexus OS
Hello,i have created a route-map and i want to apply it on an interface PortChannel but the command is not working.It seems that there is no ip policy command.Note that i did the same command on another VDC and it works fine.Does i need to activate s...
Bonjour Communauté Cisco, Je rencontre un problème lors du téléchargement des fichiers OVA de Cisco ACI Simulator 6.0(1g) depuis mon compte Cisco. Plus précisément, je reçois le message suivant : "Droit requis. Cliquez pour obtenir de l'aide." Cepend...
By default ACI multipod IPN L3out OSPF external network are E2. I have requirement to change them to type E1. is it possible ? how? I tried to configure route map default export to change E2 to E1 but it did not work.
