08-09-2014 10:42 AM - edited 03-16-2019 11:41 PM
Hi
CIsco 7960 IP Phone was upgraded firmware from sccp to sip. It has taken firmware correctly but not registering with CME on the local router. I configured Voice register global, voice register dn, voice register pool. All phones are taking extention numbers configured 5000, 5001, 5002. But not registering with CME so that I can make internal calls each other. when I reload CME router, phones are not reloading itself. All phones have taken IP from DHCP pool and even extensions but not registered.
Please suggest me configuration to register phones with CME. Do I need to register it to sip registrar server to make call on other extendions on the same LAN?
Status Message On IP 7960 Phone:
W310 12 error(s) Parsing
SIPDefault.cnf
W320 5 error Parsing
SIPP0002B9AFC0F7.cnf
W360 no DNS server Active
E600 REG send failure
REGISTER
E102 MISC Error: No Time
server
W350 invalid proxy_backup
W351 invalid proxy_emergency
CME# sh voice register pool all
Pool Tag 1
Config:
Mac address is 0003.6B54.BCD9
Type is 7960
Number list 1 : DN 1
Proxy Ip address is 0.0.0.0
DTMF Relay is disabled
Call Waiting is enabled
DnD is disabled
Video is disabled
Camera is disabled
Busy trigger per button value is 0
keep-conference is enabled
registration expires timer max is 600 and min is 60
username redoq password redoq123
dialplan tag is 1
Lpcor Type is none
blf call list is enabled
Transport type is udp
service-control mechanism is not supported
Registration method: per line
Privacy feature is not configured.
Privacy button is disabled
Reason for unregistered state:
No registration request since last reboot/unregister
Dialpeers created:
Statistics:
Active registrations : 0
Total SIP phones registered: 0
Total Registration Statistics
Registration requests : 0
Registration success : 0
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time :
Last unregister request time :
Register success time :
Unregister success time :
Pool Tag 2
Config:
Mac address is 0030.94C4.5009
Type is 7960
Number list 1 : DN 2
Proxy Ip address is 0.0.0.0
DTMF Relay is disabled
Call Waiting is enabled
DnD is disabled
Video is disabled
Camera is disabled
Busy trigger per button value is 0
keep-conference is enabled
registration expires timer max is 600 and min is 60
username redoq1 password redoq123
dialplan tag is 1
Lpcor Type is none
Transport type is udp
service-control mechanism is not supported
Registration method: per line
Privacy feature is not configured.
Privacy button is disabled
Reason for unregistered state:
No registration request since last reboot/unregister
Dialpeers created:
Statistics:
Active registrations : 0
Total SIP phones registered: 0
Total Registration Statistics
Registration requests : 0
Registration success : 0
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time :
Last unregister request time :
Register success time :
Unregister success time :
Pool Tag 3
Config:
Mac address is 0002.B9AF.C0F7
Type is 7960
Number list 1 : DN 3
Proxy Ip address is 0.0.0.0
DTMF Relay is disabled
Call Waiting is enabled
DnD is disabled
Video is disabled
--More-- Camera is disabled
Busy trigger per button value is 0
keep-conference is enabled
registration expires timer max is 600 and min is 60
username redoq2 password redoq123
dialplan tag is 1
Lpcor Type is none
Transport type is udp
service-control mechanism is not supported
Registration method: per line
Privacy feature is not configured.
Privacy button is disabled
Reason for unregistered state:
No registration request since last reboot/unregister
Dialpeers created:
Statistics:
Active registrations : 0
Total SIP phones registered: 0
Total Registration Statistics
Registration requests : 0
Registration success : 0
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time :
Last unregister request time :
Register success time :
Unregister success time :
RedoqCME(config)#voice register global
RedoqCME(config-register-global)#reset
No contact info available for pool 1.
No contact info available for pool 2.
No contact info available for pool 3.
No contact info available for pool 4.
RedoqCME(config-register-global)#^Z
RedoqCME#sh run
Building configuration...
Current configuration : 9361 bytes
!
! Last configuration change at 17:04:55 UTC Sat Aug 9 2014 by redoq
! NVRAM config last updated at 14:46:12 UTC Sat Aug 9 2014
! NVRAM config last updated at 14:46:12 UTC Sat Aug 9 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname RedoqCME
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
network-clock-participate wic 0
!
no ipv6 cef
ip source-route
ip cef
!
!
!
ip dhcp excluded-address 10.10.1.1 10.10.1.10
ip dhcp excluded-address 10.15.1.1 10.15.1.10
!
ip dhcp pool DATA
network 10.10.1.0 255.255.255.0
default-router 10.10.1.1
!
ip dhcp pool VOICE
network 10.15.1.0 255.255.255.0
default-router 10.15.1.1
option 150 ip 10.15.1.1
!
!
!
multilink bundle-name authenticated
!
!
!
!
isdn switch-type basic-net3
!
!
trunk group ext
!
crypto pki token default removal timeout 0
!
!
voice-card 0
codec complexity high
!
!
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
h323
h225 timeout ntf 500
call preserve
h245 caps mode restricted
modem passthrough nse codec g711ulaw
sip
registrar server expires max 600 min 60
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
!
voice class h323 1
h225 timeout tcp establish 3
!
!
voice register global
mode cme
source-address 10.15.1.1 port 5060
max-dn 20
max-pool 10
load 7960-7940 P0S3-07-5-00
call-forward system redirecting-expanded
tftp-path flash:
create profile sync 000164329254815A
network-locale GB
network-locale 1 GB
network-locale 2 GB
!
voice register dn 1
number 5000
name SIP 1
allow watch
!
voice register dn 2
number 5001
allow watch
name SIP 2
voice register dn 3
number 5002
allow watch
name SIP 3
!
voice register dn 4
number 5003
allow watch
name SIP 4
!
voice register dialplan 1
type 7940-7960-others
pattern 1 5...
pattern 2 5000
pattern 3 5001
pattern 4 5002
pattern 5 5003
!
voice register dialplan 2
type 7940-7960-others
pattern 2 01782......
!
voice register pool 1
id mac 0003.6B54.BCD9
type 7960
number 1 dn 1
dialplan 1
presence call-list
username redoq password redoq123
codec g711ulaw
!
voice register pool 2
id mac 0030.94C4.5009
type 7960
number 1 dn 2
dialplan 1
username redoq1 password redoq123
!
voice register pool 3
id mac 0002.B9AF.C0F7
type 7960
number 1 dn 3
dialplan 1
username redoq2 password redoq123
!
voice register pool 4
id mac 0003.6B75.A91C
type 7960
number 1 dn 4
dialplan 1
!
voice hunt-group 1 sequential
final 5003
list 5000,5001,5002
timeout 20
pilot 5900
!
!
!
!
!
license udi pid CISCO2911/K9 sn xxxxxxxxxxxxxxx
license boot module c2900 technology-package securityk9
license boot module c2900 technology-package uck9
license boot module c2900 technology-package datak9
hw-module pvdm 0/0
!
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
ip address 1.1.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
!
interface GigabitEthernet0/1.1
encapsulation dot1Q 1
ip address 10.1.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface GigabitEthernet0/1.10
encapsulation dot1Q 10 native
ip address 10.10.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface GigabitEthernet0/1.15
encapsulation dot1Q 15
ip address 10.15.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface GigabitEthernet0/2
no ip address
shutdown
duplex auto
speed auto
!
!
!
!
!
router eigrp 100
network 10.0.0.0
!
ip forward-protocol nd
!
ip http server
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 36000 requests 10000
ip http path flash:gui
!
!
!
!
!
!
tftp-server flash:P0S3-07-5-00.bin
tftp-server flash:P0S3-07-5-00.loads
tftp-server flash:P0S3-07-5-00.sb2
tftp-server flash:P003-07-5-00.sbn
tftp-server flash:OS79XX.TXT
!
control-plane
!
!
voice-port 0/0/0
input gain 4
compand-type a-law
cptone GB
timeouts call-disconnect 5
timeouts wait-release 5
connection plar 5900
bearer-cap Speech
!
voice-port 0/0/1
input gain 4
compand-type a-law
cptone GB
timeouts call-disconnect 5
timeouts wait-release 5
connection plar 5900
bearer-cap Speech
!
voice-port 0/2/0
supervisory disconnect dualtone pre-connect
supervisory answer dualtone sensitivity high
no battery-reversal
soft-offhook
input gain 4
cptone GB
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 5000
impedance complex2
bearer-cap Speech
caller-id enable
!
mgcp profile default
!
!
!
!
presence
presence call-list
!
sip-ua
!
!
!
gatekeeper
shutdown
!
!
!
line con 0
password ********
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
exec-timeout 0 0
privilege level 15
password *******
logging synchronous
login local
transport input all
transport output all
!
scheduler allocate 20000 1000
end
08-10-2014 03:19 AM
Apart from the 7960/7940 being horrible SIP phones, you could try to debug SIP and see what is happening:
debug ccsip messages
Do the phone's try to register?
What is the response from the CME?
JH
08-10-2014 08:02 AM
Hi JH,
following output are shown in debug: Its not even tries to register.
edoqCME#debug ccsip all
This may severely impact system performance. Continue? [confirm]
All SIP Call tracing is enabled
RedoqCME#
Aug 10 14:43:20.981: //-1/xxxxxxxxxxxx/SIP/Transport/sipInstanceHandleConnAgeing: Connection=0x313BDCB0, addr=192.99.44.159, port=5070, connid=2 has been aged out
Aug 10 14:43:20.981: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportPostCloseConnection: Posting UDP conn close for addr=192.99.44.159, port=5070, local_addr=, connid=2
Aug 10 14:43:20.981: //-1/xxxxxxxxxxxx/SIP/Transport/sipDeleteConnInstance: Deleted conn=0x313BDCB0, connid=2, addr=192.99.44.159, port=5070, local_addr=, transport=UDP
Aug 10 14:43:20.981: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportSetAgeingTimer: Aging timer initiated for holder=0x31C7DA20,addr=192.99.44.159
Aug 10 14:43:20.981: //-1/xxxxxxxxxxxx/SIP/Transport/sipTransportStopAgeingTimer: Aging timer stopped for holder=0x31C7DA20,addr=192.99.44.159
Aug 10 14:43:20.981: //-1/xxxxxxxxxxxx/SIP/Transport/sipDeleteConnHolder: Deleted holder=0x31C7DA20, addr=192.99.44.159, count=0
Aug 10 14:43:20.981: //-1/xxxxxxxxxxxx/SIP/Info/udpsock_close_connect: Socket fd: 1 closed for connid 2 with remote port: 5070.
08-10-2014 09:40 AM
Content-Length: 0
Aug 10 16:25:34.233: //21260/BE352700A9F5/SIP/Error/act_disconnecting_wait_ack: Out of retries
Aug 10 16:25:34.233: //21260/BE352700A9F5/SIP/Info/sipSPIIcpifUpdate: CallState: 2 Playout: 0 DiscTime:9419916 ConnTime 0
Aug 10 16:25:34.233: //21260/BE352700A9F5/SIP/State/sipSPIChangeState: 0x319C0C20 : State change from (STATE_DISCONNECTING, SUBSTATE_NONE) to (STATE_DEAD, SUBSTATE_NONE)
Aug 10 16:25:34.233: //21260/BE352700A9F5/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x319C0C20
State of The Call : STATE_DEAD
TCP Sockets Used : NO
Calling Number : 1213
Called Number : 972592253743
Source IP Address (Sig ): 86.183.210.11
Destn SIP Req Addr:Port : 23.95.82.42:5077
Destn SIP Resp Addr:Port : 23.95.82.42:5077
Destination Name : 23.95.82.42
08-10-2014 10:40 AM
Just a suggestion:
try binding control and source interface of sip to whatever you have configured for voice register global
Voice service voip
sip
bind all <source interface>
and add option 150 in Data VLan also.
by the what do you see in status message on the phone.
on the phone it will be under
setting-->status-->status messages
you can also do "debug voice register events" and "debug voice register errors" to capture the registration process. (dont forget to do term mon)
regards
Chintan
08-10-2014 12:30 PM
Hi Chintan,
Thanks for you suggeation. Fing attached image file for status message on IP phone. its behaving same way.
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
h323
h225 timeout ntf 500
call preserve
h245 caps mode restricted
modem passthrough nse codec g711ulaw
sip
bind control source-interface GigabitEthernet0/1.15
bind media source-interface GigabitEthernet0/1.15
registrar server
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
!
voice class h323 1
h225 timeout tcp establish 3
!
!
!
!
sh voice register global output after the configuration metioned by you.
CME#sh voice register global
CONFIG [Version=8.6]
========================
Version 8.6
Mode is cme
Max-pool is 10
Max-dn is 20
Outbound-proxy is enabled and will use global configured value
Security Policy: DEVICE-DEFAULT
Forced Authorization Code Refer is enabled
Source-address is 10.15.1.1 port 5060
Load 7960-40 is P0S3-07-5-00
Time-format is 12
Date-format is M/D/Y
Time-zone is 5
Hold-alert is disabled
Mwi stutter is disabled
Mwi registration for full E.164 is disabled
Forwarding local is enabled
Video is disabled
Camera is disabled
Privacy is enabled
Privacy-on-hold is disabled
Dst auto adjust is enabled
start at Apr week 1 day Sun time 02:00
stop at Oct week 8 day Sun time 02:00
Call List BLF is enabled
Max redirect number is 5
IP QoS DSCP:
ef (the MS 6 bits, 46, in ToS, 0xB8) for media
cs3 (the MS 6 bits, 24, in ToS, 0x60) for signal
af41 (the MS 6 bits, 34, in ToS, 0x88) for video
default (the MS 6 bits, 0, in ToS, 0x0) for service
Telnet Level: 0
Tftp path is flash:
Generate text file is disabled
Tftp files are created, current syncinfo 0001643292548154
OS79XX.TXT is not created
timeout interdigit 10
network-locale[0] GB (This is the default network locale for this box)
network-locale[1] GB
network-locale[2] GB
network-locale[3] US
network-locale[4] US
user-locale[0] US (This is the default user locale for this box)
user-locale[1] US
user-locale[2] US
user-locale[3] US
user-locale[4] US Active registrations : 0
Total SIP phones registered: 0
Total Registration Statistics
Registration requests : 0
Registration success : 0
08-10-2014 01:45 PM
looks like your phone is not able to parse SIP config file and that is why it not able to find CME.
are you runnig mix of both SCCP and SIP phones or only SIP phones?
if you are running only SIP phones, you can Try below.
i see "OS79XX.TXT is not created" in your configuration, to solve this
create OS79XX.txt file, and put it on tftp server.
the OS79XX contents should be single line, that is phone firmware.
create a text file:
put content as firmware that phone shoud use, in your case it will be
P0S3-07-5-00
save file as OS79XX.txt
put the saved file on any tftp server.
copy the file into routers flash
"copy tftp flash" and then give tftp server address and file name.
after succesfully fetching the file in your flash, make it avalable for CME s tftp server
(config)#tftp-server flash:OS79XX.txt
after that, issue comand create profile, and upgrade in Voice register global
#create profile
#upgrade
after all this if you issue "sh voice register global", you should see OS79XX.txt Created.
once all this done, do hard reset of IP phone and see if it is registering or not.
regards
Chintan
08-10-2014 02:56 PM
Hi,
i am running only sip right now. I have done all that but still not registering
edoqCME(config-register-global)#^Z
RedoqCME#
Aug 10 21:38:27.635: %SYS-5-CONFIG_I: Configured from console by console
RedoqCME#sh voice register global
CONFIG [Version=8.6]
========================
Version 8.6
Mode is cme
Max-pool is 10
Max-dn is 20
Outbound-proxy is enabled and will use global configured value
Security Policy: DEVICE-DEFAULT
Forced Authorization Code Refer is enabled
Source-address is 10.15.1.1 port 5060
Load 7960-40 is P0S3-07-5-00
Time-format is 12
Date-format is M/D/Y
Time-zone is 5
Hold-alert is disabled
Mwi stutter is disabled
Mwi registration for full E.164 is disabled
Forwarding local is enabled
Video is disabled
Camera is disabled
Privacy is enabled
Privacy-on-hold is disabled
Dst auto adjust is enabled
start at Apr week 1 day Sun time 02:00
stop at Oct week 8 day Sun time 02:00
Call List BLF is enabled
Max redirect number is 5
IP QoS DSCP:
ef (the MS 6 bits, 46, in ToS, 0xB8) for media
cs3 (the MS 6 bits, 24, in ToS, 0x60) for signal
af41 (the MS 6 bits, 34, in ToS, 0x88) for video
default (the MS 6 bits, 0, in ToS, 0x0) for service
Telnet Level: 0
Tftp path is flash:
Generate text file is disabled
Tftp files are created, current syncinfo 0001643292548159
OS79XX.TXT is created.
timeout interdigit 10
network-locale[0] GB (This is the default network locale for this box)
network-locale[1] GB
network-locale[2] GB
network-locale[3] US
network-locale[4] US
user-locale[0] US (This is the default user locale for this box)
user-locale[1] US
user-locale[2] US
user-locale[3] US
user-locale[4] US Active registrations : 0
Total SIP phones registered: 0
Total Registration Statistics
Registration requests : 0
Registration success : 0
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time :
Last unregister request time :
Register success time :
Unregister success time :
Thanks
Regards
08-10-2014 03:17 PM
ok, can you check your phone and see what firmware its running. i am suspecting firmware has not been updted correctly.it would be probaly there in settings.
aslo please share full set of status message what you are seeing on phone when it is booting up and registering.
also form your CME, please previde output of below.
more flash:SIPDefault.cnf
regards,
Chintan
08-10-2014 04:36 PM
Hi
The following steps are taken when phone boots up
1. Configuring vlan
2. Configuring IP
3. TFTP P0S3-07-5-00.loads
4. Configuring vlan (again)
5. Configuring IP (again)
6. Requsting Configuration
7. Get extention number (done)
Find attachment for few status on phone.
Its not registering with that is why there is no message from CME.
SHOW FLAH:
65 10800 Nov 19 2012 22:51:18 +00:00 ringtones/Sax1.raw
166 14160 Nov 19 2012 22:51:20 +00:00 ringtones/Sax2.raw
167 16080 Nov 19 2012 22:51:20 +00:00 ringtones/Vibe.raw
169 461 Aug 5 2014 09:48:44 +00:00 P0S3-07-5-00.loads
170 689278 Aug 5 2014 09:47:38 +00:00 P0S3-07-5-00.bin
171 689682 Aug 5 2014 09:49:46 +00:00 P0S3-07-5-00.sb2
172 69 Aug 10 2014 21:48:56 +00:00 syncinfo.xml
173 1142 Dec 6 2012 11:19:58 +00:00
174 4866 Dec 5 2013 00:15:48 +00:00 cdr.RedoqCME.12_04_2013_01_15_49.967
175 14429 Dec 6 2013 00:15:50 +00:00 cdr.RedoqCME.12_05_2013_01_15_50.229
176 4843 Dec 7 2013 00:15:50 +00:00 cdr.RedoqCME.12_06_2013_01_15_50.459
177 8769 Dec 8 2013 00:15:50 +00:00 cdr.RedoqCME.12_07_2013_01_15_50.789
178 6231 Dec 9 2013 00:15:50 +00:00 cdr.RedoqCME.12_08_2013_01_15_51.119
179 204 Dec 9 2013 17:15:50 +00:00 cdr.RedoqCME.12_09_2013_01_15_51.345
180 2004 Aug 10 2014 21:48:58 +00:00 SIPDefault.cnf
181 4342 Aug 10 2014 21:48:58 +00:00 softkeyDefault_kpml.xml
182 4376 Aug 10 2014 21:49:00 +00:00 softkeyDefault.xml
183 4342 Aug 8 2014 08:10:44 +00:00 softkey1_kpml.xml
184 4376 Aug 8 2014 08:10:44 +00:00 softkey1.xml
185 327 Aug 10 2014 21:49:00 +00:00 cme_dialplan_1.xml
186 12 Aug 10 2014 21:02:04 +00:00 OS79XX.txt
187 129292 Aug 5 2014 09:50:44 +00:00 P003-07-5-00.sbn
188 134 Aug 10 2014 21:49:02 +00:00 cme_dialplan_2.xml
189 825 Aug 10 2014 21:49:02 +00:00 featurePolicyDefault.xml
190 825 Aug 8 2014 08:10:46 +00:00 featurePolicy1.xml
191 1331 Aug 10 2014 21:49:02 +00:00 SIP00036B54BCD9.cnf
192 1329 Aug 10 2014 21:49:02 +00:00 SIP003094C45009.cnf
193 1329 Aug 10 2014 21:49:04 +00:00 SIP0002B9AFC0F7.cnf
194 1315 Aug 10 2014 21:49:04 +00:00 SIP00036B75A91C.cnf
Thank You
08-10-2014 08:52 PM
i am getting clueless :)
lets give one more try:
can share out put of below commands
"sh voice register tftp-bind"
"more flash:/SIPDefault.cnf"
regards
Chintan
08-11-2014 12:01 AM
Hi,
I appreciate your efforts. I think that I sould start configuring CME router to register with SIP registrar server. Once I configure SIP channels ( username and password authentication) it may start working.
Please find output below:
CME#more flash:/SIPDefault.cnf
image_version: "P0S3-07-5-00";
call_manager1_addr: "10.15.1.1";
call_manager2_addr: "";
call_manager3_addr: "";
call_manager4_addr: "";
call_manager1_sip_port: "5060";
call_manager2_sip_port: "";
call_manager3_sip_port: "";
call_manager4_sip_port: "";
proxy1_address: "USECALLMANAGER";
proxy2_address: "";
proxy3_address: "";
proxy4_address: "";
proxy5_address: "";
proxy6_address: "";
proxy1_port: "5060";
proxy2_port: "";
proxy3_port: "";
proxy4_port: "";
proxy5_port: "";
proxy6_port: "";
proxy_register: "1";
time_zone: "PST";
dst_auto_adjust: "1";
dst_start_month: "April";
dst_start_day: "";
dst_start_day_of_week: "Sun";
dst_start_week_of_month: "1";
dst_start_time: "02:00";
dst_stop_month: "October";
dst_stop_day: "";
dst_stop_day_of_week: "Sun";
dst_stop_week_of_month: "8";
dst_stop_time: "02:00";
date_format: "M/D/Y";
time_format_24hr: "0";
local_cfwd_enable: "1";
directory_url: "";
messages_uri: "";
services_url: "http://10.15.1.1:80/CMEserverForPhone/serviceurl";
logo_url: "";
stutter_msg_waiting: "0";
sync: "0001643292548153";
telnet_level: "0";
autocomplete: "1";
call_stats: "0";
Domain_Name: "";
dtmf_avt_payload: "101";
dtmf_db_level: "3";
dtmf_inband: "1";
dtmf_outofband: "avt";
dyn_dns_addr_1: "";
dyn_dns_addr_2: "";
dyn_tftp_addr: "";
end_media_port: "32766";
http_proxy_addr: "";
http_proxy_port: "80";
nat_address: "";
nat_enable: "0";
nat_received_processing: "0";
network_port2_type: "Hub/Switch";
outbound_proxy: "";
outbound_proxy_port: "5060";
proxy_backup: "USECALLMANAGER";
proxy_backup_port: "5060";
proxy_emergency: "USECALLMANAGER";
proxy_emergency_port: "5060";
remote_party_id: "0";
sip_invite_retx: "6";
sip_retx: "10";
sntp_mode: "directedbroadcast";
sntp_server: "0.0.0.0";
start_media_port: "16384";
tftp_cfg_dir: "";
timer_invite_expires: "180";
timer_register_delta: "5";
timer_register_expires: "3600";
timer_t1: "500";
timer_t2: "4000";
dscpForAudio : 184;
dscpVideo : 136;
dscpForSCCPPhoneServices : 0;
dscpForCm2Dvce : 96;
voip_control_port: "5060";
CME#show voice register tftp-bind
tftp-server syncinfo.xml url flash:/syncinfo.xml
tftp-server SIPDefault.cnf url flash:/SIPDefault.cnf
tftp-server softkeyDefault_kpml.xml url flash:/softkeyDefault_kpml.xml
tftp-server softkeyDefault.xml url flash:/softkeyDefault.xml
tftp-server cme_dialplan_1.xml url flash:/cme_dialplan_1.xml
tftp-server cme_dialplan_2.xml url flash:/cme_dialplan_2.xml
tftp-server featurePolicyDefault.xml url flash:/featurePolicyDefault.xml
tftp-server SIP00036B54BCD9.cnf url flash:/SIP00036B54BCD9.cnf
tftp-server SIP003094C45009.cnf url flash:/SIP003094C45009.cnf
tftp-server SIP0002B9AFC0F7.cnf url flash:/SIP0002B9AFC0F7.cnf
tftp-server SIP00036B75A91C.cnf url flash:/SIP00036B75A91C.cnf
Thank You.
08-11-2014 12:17 AM
i dont any clue now :-), but i feel that your phone is not able to understand SIP cnf files. and all configuration looks correct.
lets see some one else here can help you.
regards
Chintan
08-11-2014 02:44 AM
Chintan,Thanks for your well try.
Can Anyone save my hair pleaseeee!!
08-11-2014 09:05 AM
Can you try one thing..
Apply below commands under sip register global
authenticate register
authenticate realm all
create profile
If no success, then try to factory reset one of the phone.
Suresh
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide