cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1014
Views
10
Helpful
5
Replies

Cisco IAD2432 dial-peer In out ?

PseudoCyber
Level 1
Level 1

Hey all
In no way am I experienced in Cisco switch/router/IAD provisioning

But i have programmed a few PBX in my time

Having a tough time getting inward calls from My T1 pri to get to The Analog FXS port on a IAD2432

I'm pretty sure its a Dial-peer issue
If you could Take a look and tell me what I'm doing wrong?

outward calls work

There's only 4 analog

ANY help would be appreciated   ... (I have cookies!)


Dial-peer
SBWROUTER#show runn | b dial-peer
dial-peer voice 3 pots
preference 2
destination-pattern 8505
port 2/2
!
dial-peer voice 10 pots
destination-pattern .T
port 1/0:23
forward-digits all
!
dial-peer voice 1 pots
destination-pattern 8505
port 2/0
!
dial-peer voice 2 pots
destination-pattern 8505
port 2/1
!
dial-peer voice 12 pots
incoming called-number .
direct-inward-dial
port 1/0:23
!
dial-peer voice 4 pots
destination-pattern 8505
port 2/3
!
!
dial-peer hunt 7
Thanks in advance for any help

 

1 Accepted Solution

Accepted Solutions

One Recommendation, try to avoid .T for outgoing dial-peers. Make it more precise. 

 

dial-peer voice 10 pots
destination-pattern .T
port 1/0:23
forward-digits all

 

You have dial-peers pointing to FXS ports with 8XXX. What called informations does your ISP sends, is it a full digit or 4 digit? You might need to do translation. Is it a CME or CUCM deployment ? 

can you share the output of debug isdn q931 and debug voice ccapi inout. 



Response Signature


View solution in original post

5 Replies 5

One Recommendation, try to avoid .T for outgoing dial-peers. Make it more precise. 

 

dial-peer voice 10 pots
destination-pattern .T
port 1/0:23
forward-digits all

 

You have dial-peers pointing to FXS ports with 8XXX. What called informations does your ISP sends, is it a full digit or 4 digit? You might need to do translation. Is it a CME or CUCM deployment ? 

can you share the output of debug isdn q931 and debug voice ccapi inout. 



Response Signature


Thanks for the reply Nithin,

Outbound calls - do I need <xNum> dial-peers? Not sure what else to use ... they (end-user) calls all over the world!

It a full XXX-xxx-XXXX 10 digits on the inward calls

I'm thinking it's a CME (not really hip to the cisco lingo)

it's a small company, not enterprise

TBH it looks like its looping on the debug ... just scrolls and scrolls

not that it helps but I think it's IOS 12.4 ...

Thanks for the Help (what kind of cookies do you like?)

(debug logs attached)

 

Nithin,

Thank You!

Yes the ".T" on the outbound calls was "looping" the T1 and generally causing issues

Had to fully "break-out" the dial-peers and translations

You're the best!

Here's a cupcake ... sorry ran out of cookies

___________________¶¶¶¶¶¶
_________________¶¶¶¶¶___¶¶
________________¶¶¶¶¶¶¶___¶
_______________¶¶¶¶¶¶¶¶¶¶¶¶¶
___________¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶
________¶¶¶¶¶___¶¶¶¶¶¶¶¶¶¶¶____¶¶¶¶¶
_____¶¶¶¶_________¶¶¶¶¶¶¶__________¶¶¶
____¶¶¶______¶____________________¶__¶¶¶
___¶¶________¶¶__¶¶_____¶¶__¶¶¶________¶¶
__¶¶_______________¶¶__¶¶_____¶¶¶_______¶¶
_¶¶______________________________________¶
¶¶________________________________________¶
¶¶________________________________________¶
_¶¶¶____________________________________¶¶
___¶¶¶¶¶____________________________¶¶¶¶¶
____¶¶_¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶_¶
_____¶____¶_____¶____¶¶____¶_____¶¶___¶¶
_____¶____¶¶____¶____¶¶____¶_____¶____¶
_____¶¶____¶____¶¶___¶¶___¶¶____¶¶___¶¶
______¶____¶¶___¶¶___¶¶___¶¶____¶____¶
______¶¶____¶___¶¶___¶¶___¶¶___¶¶___¶¶
_______¶____¶¶___¶___¶¶___¶____¶¶___¶
_______¶¶___¶¶___¶___¶¶___¶____¶___¶¶
________¶____¶¶__¶¶__¶¶__¶¶___¶¶___¶
________¶¶____¶___¶__¶¶__¶___¶¶__¶¶
_________¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶

Scott Leport
Level 7
Level 7

Hi,

 

The call is looping between dial-peer 12 and dial-peer 10. So the dialled number isn't matching your destination-patterns attached to your FXS lines.

 

Might be better to see your config, but I suspect you'll need to modify or create some voice translation rule settings to translate the dialled number attached to your FXS lines.

Scott,

Thanks for the reply

You're right, that's exactly what I had to do

I was hoping not to get that far into it, but I should know better

Have a coffee on me...

 

_________________¶¶¶1___¶¶¶____¶¶¶1_______________
__________________¶¶¶____¶¶¶____1¶¶1______________
___________________¶¶¶____¶¶¶____¶¶¶______________
___________________¶¶¶____¶¶¶____¶¶¶______________
__________________¶¶¶____1¶¶1___1¶¶1______________
________________1¶¶¶____¶¶¶____¶¶¶1_______________
______________1¶¶¶____¶¶¶1___¶¶¶1_________________
_____________¶¶¶1___1¶¶1___1¶¶1___________________
____________1¶¶1___1¶¶1___1¶¶1____________________
____________1¶¶1___1¶¶1___1¶¶¶____________________
_____________¶¶¶____¶¶¶1___¶¶¶1___________________
______________¶¶¶¶___1¶¶¶___1¶¶¶__________________
_______________1¶¶¶1___¶¶¶1___¶¶¶¶________________
_________________1¶¶1____¶¶¶____¶¶¶_______________
___________________¶¶1____¶¶1____¶¶1______________
___________________¶¶¶____¶¶¶____¶¶¶______________
__________________1¶¶1___1¶¶1____¶¶1______________
_________________¶¶¶____¶¶¶1___1¶¶1_______________
________________11_____111_____11_________________
__________¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶________
1¶¶¶¶¶¶¶¶¶¶¶__¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶________
1¶¶¶¶¶¶¶¶¶¶¶__1¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶________
1¶¶_______¶¶__1¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶________
1¶¶_______¶¶__1¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶________
1¶¶_______¶¶__¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶________
1¶¶_______¶¶__1¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶________
_¶¶¶¶¶¶¶¶¶¶¶__¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶________
_¶¶¶¶¶¶¶¶¶¶¶__¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶________
__________¶¶___1¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶1________
__________1¶¶___¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶_________
____________¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶11__________
11_____________________________________________111
1¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶1
__¶¶111111111¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶¶111111111¶__