12-20-2012 02:24 AM - edited 03-16-2019 02:49 PM
Hi guys,
here is a short CME hunt group config:
voice hunt-group 1 parallel
pilot 100
list 200, 300
timeout 20
final 4000
Users 200 and 300 have their own Mailboxes.
4000 is a separate Voicemail.
How do the users know that someone has left a message on 4000?
Thanks.
Best regards
Solved! Go to Solution.
12-20-2012 04:09 AM
Cristian,
You will need to configure a GDM to achieve this. According to Unity Express design Guide from this doc
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/design/design21/cuevmdes.html#wp1013248
Any phone with a button appearance of the extension associated with the group receives MWI for message content in the GDM. This configuration is shown in Figure 26. The customer-service GDM extension (1050) appears on button 2 of group member User2 U2's phone (extension 1001).
That suggests that you need to do the ff:
1. Configure a GDM
2. Assign the enxtensions 200,300 to the GDM
3. Assign the number of the GDM to an available button of these phones
Then you will need to change your hunt list config as ff:
voice hunt-group 1 parallel
pilot 100
list 200, 300
timeout 20
final 54000 (54000 will be your GDM number)
Then you need to ocnfigure this
ephone-dn x
number 54000
call-forward all 4000 (assuming 4000 is your VM pilot)
So when the call goes to VM for extension 54000, all the users in that mailbox will be notified.
That what I could think of
Please rate all useful posts
"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson
12-20-2012 07:42 AM
A better and simpler way to do this is using a shared line.
That will also support MWI and avoid the complication of GDM.
12-20-2012 02:53 AM
The message will be left for 100.
4000 is supposed to be your VM number.
12-20-2012 03:00 AM
from what I've understood is so:
When callers dial extension 100, extensions 200 and 300 ring simultaneously.
if none of the extensions answer, the call is forwarded to extension 4000, which is the number for the voice-mail service.
how are the user notified that someone has left a message? supposing no one answers.
the system is a CME/CUE 9.0/8.6.4.
Thanks.
12-20-2012 03:36 AM
Cristian,
Its been a while I did this, but from my old notes I came up with this..Try and see if it works
Add extensions 200 and 300 as the e164 number for extension 100.
Please rate all useful posts
"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson
12-20-2012 03:48 AM
sorry but I can't see where you're going. I think I wasn't clear enough.
what I'd like to do is: when someone calls 100 both phones should ring simultaneously. if no one answers, the call should go to a "generic" voicemail box. (not the users own mailboxes).
the question is: how can the users be notified that someone has left a message for that "generic" mailbox?
Thanks.
12-20-2012 04:09 AM
Cristian,
You will need to configure a GDM to achieve this. According to Unity Express design Guide from this doc
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/design/design21/cuevmdes.html#wp1013248
Any phone with a button appearance of the extension associated with the group receives MWI for message content in the GDM. This configuration is shown in Figure 26. The customer-service GDM extension (1050) appears on button 2 of group member User2 U2's phone (extension 1001).
That suggests that you need to do the ff:
1. Configure a GDM
2. Assign the enxtensions 200,300 to the GDM
3. Assign the number of the GDM to an available button of these phones
Then you will need to change your hunt list config as ff:
voice hunt-group 1 parallel
pilot 100
list 200, 300
timeout 20
final 54000 (54000 will be your GDM number)
Then you need to ocnfigure this
ephone-dn x
number 54000
call-forward all 4000 (assuming 4000 is your VM pilot)
So when the call goes to VM for extension 54000, all the users in that mailbox will be notified.
That what I could think of
Please rate all useful posts
"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson
12-20-2012 07:42 AM
A better and simpler way to do this is using a shared line.
That will also support MWI and avoid the complication of GDM.
12-20-2012 07:48 AM
do you mean?
voice hunt-group 1 parallel
pilot 100
list 200, 300
timeout 20
final 4000
ephone-dn 1
number 200
ephone-dn 2
number 4000
call-forward all 5555 -> voicemail
ephone 1
button 1:1 2:2
Thanks.
12-20-2012 08:15 AM
No. You can search for shared line to learn what it is.
12-20-2012 08:26 AM
Paolo's suggestion is that dont use hunt group. Configure your pilot number as a shared line on the two extensions.
Please rate all useful posts
"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson
12-20-2012 08:29 AM
thanks aokanlawon, appreciate it.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide