SRST does not work

[Gerardo Fajardo Perez]

Hi All,

Have a CUCM 8.6 BE (only Pub) and a Router (c2900-universalk9-mz.SPA.150-1.M6.bin). Both are configured to have SRST, and when accesing "Telephone Information" at IPPhone 6921  active server and inactive server are displayed in right order. But when WAN Link goes down, IP Phone does not come up with the inactive server,

Call-manager-fallback´s  commands where accepted at router, and when "show ephone unregistered" is typed the IP Phone´s mac address appears.

Do I have missed something at Router, talking about License ?

Thanks in advanced

[Gregory Brunn]

Also I don't think you posted your full configuration.  Is this an MGCP gateway or h.323.

Check out this guide make sure everything matches up.

https://supportforums.cisco.com/docs/DOC-24097

[Gerardo Fajardo Perez]

Hi Gregory,

It is an H323 Gateway and does not appear that info you under agreement.

[Gregory Brunn]

Gerardo,

Your running configuration should look something like this

license udi pid CISCO2901/K9 sn FTXREDACTED
license accept end user agreement
hw-module pvdm 0/0

well at least it should  in the newer version of code it should.

If you don't see it make sure do a

conf t

license accept end user agreement

Make sure type yes or y

write the configuration (wr or copy run start)

If this does not work you may want to try updating your version of IOS code

[Aman Soi]

Hi Gerardo,

can u post the show version/show running/show license feature /sh license detail output?

regds,

aman

[Gregory Brunn]

Also do you have any phone at all registered you are setting your max-ephones low if you have other phones that are registered this would tell alot.  Along with Aman request above.

Here is a sample from my last srst config if it helps

call-manager-fallback

max-conferences 8 gain -6

transfer-system full-consult

timeouts interdigit 5

timeouts busy 16

ip source-address port 2000

max-ephones 42

max-dn 200 dual-line

[Aman Soi]

Hi Gerardo,

Have a look at this discussion with similar problem.

https://supportforums.cisco.com/thread/2123996

In your case , IOS version is 15.0(1)M6

regds,

aman

[Gerardo Fajardo Perez]

Hi Aman and Greg,

It was solved, it was an IOS problem. But what about the following: "License Type: Eval Right to use" and the "Period Left " ???

[Aman Soi]

Hi Perez,

thanks for update.

The ISR G2 comes with a 60-day evaluation license. After 60 days, the license changes to “right to use”.Is this what you are referring too.

what is the IOS version u are using now? can u share show version and show license detail cme-srst.

regds,

aman

[Gerardo Fajardo Perez]

Hi Aman,

So what will "rigth to use" mean, it means that will be active forever ???

Tomorrow i will share you the IOS version because right now Im  out of the Clients´s site.

Thanks in advanced 

[Aman Soi]

Hi Perez,

SRST would be active forever now.

http://blog.vuurmuur.com/?p=32

Licensing functionality is working as per design here. Cme-srst licenses are honor based and hence you have to just accept the EULA. After the 60 days of EvalRightToUse the license will change to "right to use" for 12 years

regds,

aman

[Gerardo Fajardo Perez]

Hi Aman,

Attached send you the info you asked me. As you will see, even though with command "sho license detail cme-srts" appears the same   "%Error: no license for cme-srst found  - License feature not found" , with the command "sho license" appears as "Active" in the Index 11...

What do you think ??

Thanks so much for your support.

[Gregory Brunn]

I think you are good now

Your error now looks like a typo

show license detail cme-srst not cme-srts

MTY_GONZALITOS_Branch_4082#sho license detail cme-srts

% Error: No license for cme-srts found - License feature not found

MTY_GONZALITOS_Branch_4082#sho license detail cme-srts

% Error: No license for cme-srts found - License feature not found

MTY_GONZALITOS_Branch_4082#conf t

Enter configuration commands, one per line. End with CNTL/Z.

MTY_GONZALITOS_Branc(config)#license accept end user agreement

MTY_GONZALITOS_Branc(config)#exit

MTY_GONZALITOS_Branch_4082#sho license detail cme-srts

% Error: No license for cme-srts found - License feature not

Are you still having problems with SRST?

[Gerardo Fajardo Perez]

                   HI Greg,

Now it is working, so I just have the doubt.

Thanks man.

[Gregory Brunn · Accepted solution]

Well now hopefully now you are doubt free.

Aman gave you a couple +5 for your information on the SRST eval license.

[Aman Soi]

Hi Perez,

thanks for the ratings.

You can try running the command show license detail cme-srst after 8 week and 3 days just to check the status again and share output.

Index 11 Feature: cme-srst                      

Period left: 8  weeks 3  days

Period Used: 20 hours 24 minutes

License Type: EvalRightToUse

License State: Active, In Use

License Count: 10/0  (In-use/Violation)

License Priority: Low

regds,

aman