....
....
Hello,I have a little question, I'm studying MPLS using GNS3. I made a network with 4 MPLS routers, each connected to 2 others MPLS routers and one external non-MPLS router.I try to hide all the internal MPLS routing using the "no mpls ip propagate-t...
Hi,I am stuck and I need your help to fix my CISCO 3460 router for my home lab, the router load the ios and hang after loading the interfaces.Please see below the Router IOS display:ThanksAlainCisco IOS Software, 3600 Software (C3640-JK9O3S-M), Ver...
helloI cam e across a situation in a test lab, that i don't quite understandi have two test 6PE edge routers advertising IPv6 prefixes across an IPv4 MPLS core. when advertising 'known' routes across the core this is fine, and there is reachability b...
Hi, I need some help to make the configuration below.We have a point to point metroethernet line from our telecom between our two different locations. Behind the ME swithes of teelcom there is a 6513 switch in one side and a 3845 router at the other ...
I have a Hub and Spoke MPLS VPN topology, meaning spoke to spoke traffic MUST pass through the hub. : I need to have 2 Hubs: HUB1 and HUB2 HUB1 will be primary for spoke-A, secondary for spoke-B HUB2 will be primary for spoke-B, secondary for spoke-A...
Hello all,The L2VPN between PE1 and PE2, both PE need use loopback1(just for L2 VPN) as peering.PE1----MPLS backbone----PE2The L2 VPN is working without problem. I expect use loopback1 to establish LDP neighbor, but LDP neigbor established between PE...
Hiif l want to configure these VPLS configuration on a router, what IOS would l need to practise these configuration plsRouter(config)#l2 vfi name manualRouter(config-vfi)#vpn id numberRouter(config-vfi)#neighbor x.x.x.x encapsulation mplsRouter#conf...
I wants to run DHCP relay on my PE routers to issue IP to the CPEs. Is it recommended to run DHCP relay on PE?
what is port pseudowire and why is it used and is it different than the normal pseudowire.can anyone shed some light on this.cheersjack
Dear AllI am trying to test the use of ORF with extcommunity using "bgp rr-group" to make the PEs not advertise any routes with extcommunity which are not allowed on the RR using " bgp rr-group" command..I am not sure if I have misinterpreted using "...
Hi, I am trying to test all mode of MPLS QoS tunnle mode like uniform,etc.My diagram is as below:CE01 --access--> ME4900 --trunk--> PE01 --ldp--> P01 --ldp--> P02 --ldp--> PE02 --access--> CE02All traffic from CE01 are marked with DSCP AF31 an send t...
Good morning everyone.... I was wondering if someone could help me out with this?I have setup a dev lab setup to test some stuff out before I go forward and move to production but I have hit a brick wall...Here is a general setup Diagram. ...
HI Can some body guide me the advantages of IPLC vs MPLS...RgdsChandra
Hi,does anybody know what rfc's regarding mpls are supported by cisco (f.e. ASR9000 or Nexus 7000)?TiA,Stephan
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-21-2025 07:36 AM | ||
02-23-2025 02:34 PM | ||
03-19-2024 07:05 PM | ||
12-19-2023 12:41 AM | ||
12-10-2023 08:46 AM |