Could you please indicate if the SG200-08 includes support for 802 1x EAP-TLS?I am looking for a relatively low cost switch for a lab test.Thank you!
Could you please indicate if the SG200-08 includes support for 802 1x EAP-TLS?I am looking for a relatively low cost switch for a lab test.Thank you!
Is there any way to create authorization rule that combine both machine and user identity groups in one rule?for example, authorization profile match only if computer in external identity X and username in external identity group Y.
G'day All, Could someone advise if it is possible to extended or change the time profile of a guest account that has already been created? I am trying to understand using time profiles from within the Sponsor Portal. Imagine a guest user has an accou...
Hi,I have upgraded ISE from 1.3.x to 1.4 as its supports SCCM integration. However I am not seen anything under Vendor name dropdown box, as per my understanding it should show all the Microsoft patch management products including SCCM ver 4.x and 5....
We are authenticating clients for Aerohive APs on our ACS 5.1 servers. Currently our logs are getting filled with spam of invalid radius attributes. I have opened a case with them to see what is sending the request. The message is "11014 RADIUS pa...
HiOn a Catalyst 2960, I'm trying to allow a IP phone and a computer on the same port, and verify those devices against RADIUS (ISE). Unauthenticated devices should be placed in guest VLAN. In the event of a RADIUS failure, no device should be placed ...
We are deploying ACS5.5 and after some work I have been able get this to work but got another issue. Currently ACS uses AD authenticationUnder Access Policies and Service Selection Rules I crated a rule for the WLC and moved it towards the top and wa...
Hi, I need help on these errors. Here is my setup: WLC 5508 7.6.130.0 -> ACS 5.5.0.46 -> AD 2012 I am getting (2) errors in ACS 5.5 12514 EAP-TLS failed SSL/TLS handshake because of an unknown CA in the client certificates chain22044 Identity policy ...
Hi,I have a switched configured for MAB authentication with Cisco ISE. ISE is configured with AD to authenticate the users and we are using device certificate for authentication. When machine send details for authentication, many time it will send us...
All, Does anyone know if ISE can authorize MDM based on non-802.1x WLANs? Is dot1x a necessity for MDM-based authorization?
HelloI'm looking at integrating ISE (eval ver 1.4.0.253) and Prime Infrastructure (ver 2.2.0 with latest patches) to get client details pulled into Prime.Its working well with the exception of displaying usernames of users logged into AD bound PC's. ...
Have raised a TAC for this but thought I'd post here too.We are running ACS v5.4 Patch 1.We have noticed that ACS will not produce syslog messages about scheduled backups (success or failure)(1) From the GUI, under “System Administration > Config...
Hi,I am facing a problem with Cisco NAC agent Version : 4.9.5.4 and Compliance Module Version: 3.6.9845.2 such that after successfully passing through posture compliance and getting full network access, the agent will pop up again and go through post...
Dear All, We are trying to upgrade ISE from 1.2 to 1.4 but while upgrading it shows error " % Manifest file is invalid"Any ideas? Thanks in advance.
Hi everybody We are experimenting with a dot1x port authentication setup.The setup is as fallows:Microsoft 20008r2 NPSCisco 3560 compact switchCisco 3702i AP I will be using dynamic vlan assignment. So far it Works fine with pc and mac. However when ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-09-2025 09:11 PM | ||
06-19-2025 12:25 AM | ||
06-09-2025 01:32 AM | ||
06-05-2025 03:19 PM | ||
06-03-2025 11:13 AM |
User | Count |
---|---|
6 | |
4 | |
2 | |
2 | |
2 |