The Cisco Prime is not useable anymore. It was not maintained for a long time, is collecting a lot of errors and now I can't even find new Devices. My thought was to kill that thing and completely rebuild the Prime. New Server with a new Prime Instan...
Forum Posts
When we are using the switch as standalone they come up in prime.When we activate Stackwise Virtual it comes up as unsupported device in prime.We are using Cisco IOS XE Software, Version 16.12.01c on the switches. When I look through the release note...
Hi,I have 140pcs CISCO CATALYST 3560CX-12PC-S and about 10% of these have the following issue in the console. %ILPOWER-7-DETECT: Interface Gi0/2: Power Device detected: Cisco PD %ILPOWER-5-POWER_GRANTED: Interface Gi0/2: Power Granted %ILPOWER-5-IEE...
can i make two port interfaces from the same stack learn the same MAC address while port security is on? can i exclude the address from the security table so it won't count?
Hello,I recently upgraded from 15.2(7)E1 to 15.2(7)E2. After the reload all my EEM policies were no longer registered. They were also not present in the running config anymore. Try to register a policy end with the Error "EEM configuration: Unknown p...
My Nexus 7K Sup module status shows fail but the module is active. I am trying to redo the diagnosis but can seem to get the command to work on the NX-OS. I have shared the show commands below. Kindly advise if any of you come across such situation. ...
I still don't quite understand the option Peer, serve and query-only. I have some understanding about Peer, so both devices will compare each other to see which one's better but what criteria are they comparing (Stratum numer) and how the better one ...
Hi, The customer has hardware that is not supported by LMS 4.0. This will be displayed as a question mark. They have requested to change the unknown device icon from question mark to a generic icon, just colored rectangle. I have replaced the ...
how can i have a router on a stick so that the router s ip (ssh/telnet) is 10.0.0.1 vlan7the switch ip is 10.0.0.2 vlan7AND and here where i got stuck i connect a computer to the switch ports on the router (not the switch) with ip 10.0.0.10 how do i ...
Resolved! RV340 to 320 SA renewal dropping packets
I have gateway to gateway VPN between an RV340 and RV320. Inside this tunnel is a unicast video stream. It's stable and works most of the time without issue. HOWEVER once an hour enough packets get dropped that the stream goes down. it's only about 2...
Resolved! import ssl certificate for webui
hi allcan i some how import an ssl certificate for the webui?i mean a verisign ssl certificate or similar one for my.domain.name cheers rick
Hello All i m using cisco 3650 and ldap via radius (freeradius) solution to authentificate on my switchwhen i use an ldap account and its password i can access on to my switch in user modethat s workswhen i want to use mode ena i can 't use its passw...
Hi,I'm needing help to First, I installed successfully an FileZilla FTP server into a windows workstation connected to my network provider equipment. All worked properly from external side to connect to my FTP server. Then, because I need to share m...
Can I use a power injector even if my application does not require PoE? My current setup is as follows: LAN switch (WS-C3650-24PS-S) located at Point A, power injector (AIR-PWRINJ1500-2=) at Point B, and access point (AIR-AP1572EAC-B-K9) at Point C. ...
So I have the following situation:2 buildings with 2 networks of 240AC access points in mesh configuration. Each building and mesh is connected to a different internet provider, the APs connected through a SG-110-24 switch. The 2 networks are overlap...
