I want to use SNMP to get the Nexus 7K ARP table of non-default VRF, but failed. Only default VRF ARP table can be get by OID -- .1.3.6.1.2.1.4.22 -- ipNetToMediaTable.Is there any way to get ARP of non-default VRF by SNMP?
Forum Posts
dear alli have a lot of problems with a switch that was lost IOS autimatically after the power down. i have tried many ways in order to recover it but i have failed all the time. can anyone help me ? below is the error log i got Booting...Initializin...
Resolved! Problem with Netflow Egress
Dear MisterI have a 7204VXR Router, with Neflow.The collection for all interfaces is ok, but one interface (Gigabitethernet 1/0), is not showing the egress traffic in the pictures.The configuration has "ip route-cache flow", ip flow egress, and ip fl...
Hi Everyone, Is Prime Infrastructure able to export EoX report in CSV/PDF format? If yes, what are the steps to export the EoX report? Thanks!
In the PI API, specifically the "GET statisticsService" area there is a query switch to list appId. "The application Id. Use comma to seperate multiple ids."The example shows appId 1234 and 5678 which obviously does not work. - does anybody know how...
Hi,I'm making a POC network to test APIC-EM 1.5 functionalities. I've started with 8Go of RAM, upgrading to 32Go now with 8vCPU. I've installed the PNP 1.5.1.35 application, which won't launch:The unique service that isn't running is the apic-em-jbos...
Good morning all. In cisco prime we want to schedule some reports to run weekly and then being sent by Email to us. I have configure a Gmail account, (In order to use their SMTP in prime), and set the parameters inside Prime but it doesn’t work (see ...
I have a Prime 3.1.6 setup that I have tried to reset alarm email notifications to just my address. When an alert is fired (rebooted AP etc) the email is still going to 2 other people. I've tried resetting all of the alerts to default (my address):A...
Hi i have wriiteen an EEM script basic enough but contains a lot of lines for data collection which work What i want the script to do is 1 when BGP fails collects all commands and dump them into flash in TXT file (this works) 2 When BGP comes back...
Hey All - I am writing an EEM Script in order to monitor interface utilization and then sending an SNMP trap once utilization is over 50%. Just wanted to see if you all think this would work. If I gather the output from: sho interfaces $iface | i out...
Ok let's face it, not all organizations can hire people to look at alerts all day or have a fully staffed NOC. So I am on a search of conversation among other engineers on "what we monitor and why" and also the challenges of monitoring. Rather it be ...
I receieve a connection refused when attempting to run a job in Solarwinds Orion. The devices are configured for SSH and able to ping the Orion server as all the other functions for Solarwinds works, however I can't puch out a new banner to all the d...
Resolved! Wireshark capture VLAN IDs
I need to capture switchport's packets and see if a correct VLAN is set.Capture packets don't have VLAN IDs - whole header is missing. Workstation is Windows 10 with latest Intel driver and the driver has working VLAN support.Also tried ASUS USB ethe...
Hi all,I have a 3845 cisco router, i need to block access to sites such as facebook, youtube on the router itself while allowing the executive to have access to these sites. I dont have a firewall for now, can this be achieved on the router. command ...
Hi folksUsing flexible network, I'm trying to collect netflow data for vrf traffic on routers that are part of a layer-3 MPLS network. This is on Cisco ASR1001-x routers with advanced IP services.See attached diagram. I am trying to collect netflow...
