Network Management

Resolved! No devices in topology services

Hi,I have a problem with LMS 4.2, I had a lot of problem with databases who's growing, fault not true, and many others. So when i managed the database and others, i wanted to delete all the devices in Inventory,and i rediscovered t...

DFM Alerts and Activities page does not open

The DFM Alerts and Activities does not open. The customer reports error from DynAPILMS version is 3.1Thanks

Lms install without dns server and NTP

I know it sounds weird but ATM the deployment does not include this two cause the network is meant to be totally closedand ntp server will be implemented soonis there a way to ovecome this?how to set time in appliance bios? UTC? localtime?domain? (lo...

LMS to PI1.2 migration question

Hello,I want to ask 3 questions about data migration from LMS to PI1.2 as the virtual marketing synonym for the real existing product NCS1.2:1. Is there a real working and relyable data migration from LMS to PI1.2(NCS)?2. What is the minimum LMS vers...

Resolved! Unable to Access ASA5510

Hi,I have been working on figuring out a VPN problem on my companies ASA5510. I was accessing the device via: ASDM, SSH using Putty, and even initially with a console cable (also using Putty) using a computer in the networking closet. All 3 of these ...

Resolved! Event Manager question. Monitoring DNS entry.

Hello everybody,I want to use Cisco Embedded Event Manager in a router for monitoring a DNS entry that normally resolves 1.1.1.1 but if it changes to 2.2.2.2 the router has to change some access list automatically in order to permit different rou...

Resolved! SSH authentication failure CiscoWorks LMS 4

I am trying to get CiscoWorks LMS 4.0 to connect to my routers in order to back up configurations, but I am getting SSH authentication failures reported in the router logs (and archiving fails).The credentials LMS is using is a username and password ...

Resolved! Configuring email alerts from CiscoWorks LMS 4

I am looking for a way to get CiscoWorks LMS 4 to send me an email alert when a switch port goers into a security violation (err-disabled).Is there a way to do this?

Cat6509 - SNMP OIDs for interface stats

Hello,I have a Catalyst 6509-E-VSS with IOS 12.2(33)SXI3.I'm looking for OIDs to retrieve the same counters I get with the commands"show interface stats" and "show interface switching".I want to graph the number of packets that are process switched.T...

LMS 4.2.2 Fault Monitor suspend device

Hello to everyone,might sound strange but i´m looking for two hours now and can not find a way to suspend a device in the Fault Monitor. We´re using LMS 4.2.2Can someone point me to the right direction? Thank you.Regards,Chris

Cisco 891, NAT is to strict, How to open ports for all internal users to access XBOX Live.

I need to config a new 891 to allow access to all users, to access XBOX live. Im unable to get the NAT below moderate or route to more than one internal address.

OLD-CISCO-INTERFACES-MIB LocIfLoad is deprecated, what is the replacement

Hi all,i am trying to find the link saturation using OLD-CISCO-INTERFACES-MIB locIfLoad. I see that this counter is now deprecated. The replacement MIB supposed to be IF-MIB and CISCO-QUEUE-MIB. I couldn't figure out the way to find link saturation w...

Network Sniffing and Management

Hi We are looking for some free or cheap software to use on a customers network that will enable us to scan or see the network and what packets are being sent on it. We install business VOIP phones and phone systems and we get a lot of calls saying c...

LMS 4.1 - no phone registered in CUCM 6

Hi all, the customer has CUCM in the inventory database of LMS 4.1. He has all accesses from LMS to CUCM. One phone 7961 is seen in the UT report. When the customer click on the CUCM in the inventory - there is no IP phone registered in the CUCM. Wha...

TCL: Best way to store Variables between TCL script run times?

If I am simply running a TCL script every 10 seconds, how can I store varilable info between the TCL script runnings? I have tried:+ Writing the info to an EEM Variable in the Sho-Run, and then reading in this info each time the script runs, and the...

Network Management

Forum Posts

Resolved! No devices in topology services

DFM Alerts and Activities page does not open

Lms install without dns server and NTP

LMS to PI1.2 migration question

Resolved! Unable to Access ASA5510

Resolved! Event Manager question. Monitoring DNS entry.

Resolved! SSH authentication failure CiscoWorks LMS 4

Resolved! Configuring email alerts from CiscoWorks LMS 4

Cat6509 - SNMP OIDs for interface stats

LMS 4.2.2 Fault Monitor suspend device

Cisco 891, NAT is to strict, How to open ports for all internal users to access XBOX Live.

OLD-CISCO-INTERFACES-MIB LocIfLoad is deprecated, what is the replacement

Network Sniffing and Management

LMS 4.1 - no phone registered in CUCM 6

TCL: Best way to store Variables between TCL script run times?

Get ready! Great things are coming to Cisco Community

Have your wish for humanity broadcast into space by George Takei!

Cisco Business Support Virtual Assistant - Discover Support Content

ASA firewall - PacketTracer

SNMP3 Configuration

Edit Prime Infrastructure notifications

Configure Call-home using local-scripting or prime (SSM On-Prem)

SSM On-Prem issue with IP

Teams/Zoom audio drops every 15 minutes

Configuring Cisco 4G Router 1100

Confusion about how to set up Option 150

models 2960S-48FPS-L and 2960X-48TS-L are EOL ?

Cisco Router C921-4P configuration.