Hi Team: I'm trying to do a password recovery to ASA5525-x with Firepower service in referend to the guide in the link https://www.cisco.com/c/en/us/td/docs/security/asa/asa93/configuration/general/asa-general-cli/basic-hostname-pw.html#91949. We di...
Dear Team We are in the process of migrating our legacy Active/Standby ASA 5512X to a new FTD ASA 5516-X with firepower and base license. is it possible to configure Active/Standby HA with firepower device manager only without installing firepower ma...
I am thinking I need to settle with the fact the FTD-CLI seems to authenticate in this order: LOCAL then External Anyone know if there is way to get a similar result to this command in a FTD? aaa authentication ssh console ISE-RAD LOCAL Or is i...
We have a issue with Cisco prime that the context config is not saved in the running config, just the startup config. Do anyone have the same problem? In startup config it is saved, but not running config.
Hi I have upgraded the rommon, asa image and asdm image on my asa5506-x and not i cant access the device using the ASDM. It asks for the ip username etc, i enter them and it proceeds to load the software then once its loaded the software it says its ...
Hello, I have a question about a custom report, is it possible to create a custom report that shows how much data is used for facebook video for a specific subnet or host ip address? There is a predefined one, but this shows it for the complete net...
Hi, I have setup an ASA 5505 with a layer 3 switch so that I can access it with an anyconnect VPN from the outside network. I cannot ping the ASA 5505 or connect to it from the public network to the outside interface. I have shown some running config...
We configured captive portal to authenticate users with windows machines that are not joined to AD domain & for mobile devices with AD credentials. Is it possible to use third party ca certificates to avoid certificate warning ? We found that once...
Hello Team, Getting below error in FMC "there are no smart licensed devices currently being managed by the system. please go to device device management to add a smart licensed device" whereas the FMC and Smart license portal are synchronized.. ...
Hello, I have a question regarding FPR inline set configuration.We use FPR2130 with FTD as an IDS sensor (passive + SPAN) at this moment. We want to configure in-line set for another type of traffic. So, in my opinion, we have to connect another phys...
Hi Folks, Can somebody guide me how to push Cisco anyconnect posture module via ASA when a user connects anyconnect vpn. I am planing to do VPN posturing with ISE 2.2
I have set a report for "Security Intelligence Event - DNS Phishing Domain" category, IOC is "Set". So, I have attached alerts and email. Email: ===================================================================== <*- Host IOC Set From "XYZ F...
I have an ASA 5505 purchased and installed in China running asa8215-k8.bin code. No 3DES due to export controls and I can't legally install it.ASDM does not launch and from what I've read, the ssl encryption level is the issue.I can't set ssl encrypt...
Hello, since ASDM 7.92 and higher I'm facing the same problem: all ACL descriptions lines (ACE remarks) are show together in one line and for all entries in the ACL (ASDM - Configuration - Firewall - Advanced - Standard ACL). I've tested it with 7....
Hi all, I have an FMC managing a HA Pair of FTD2110's. I am using multiple interfaces on the FTD and configured each interface as a /30 point to point link since I don't want to have the GW's on the FTD. The interface to my outside network is ru...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 01-21-2026 03:34 PM | ||
| 01-21-2026 11:24 AM | ||
| 01-20-2026 01:44 PM | ||
| 12-31-2025 01:53 AM | ||
| 12-15-2025 09:32 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 3 | |
| 2 | |
| 1 |
