Hi All,I'm currently deploying an FMC 4700 appliance which I would like to connect to the network using one of the additional 10/25G SFP+ interfaces (Eth2 or Eth3) and not the default copper RJ45 interface (Eth0).I found the following document that d...
Forum Posts
Resolved! How to factory reset FMC 2500
We need to perform a factory reset on our FMC 2500 that's running 7.0.4. I've been through the CLI and did a lengthy Google search, but I'm not been able to find anything that works. Can someone provide some direction? Thank you.
Resolved! FMC/FTD Policy Migration
HiIs it possible to migrate FTD policy from an FMC both running version 7.0.x.x to a new FMC running version 7.0.x.x then upgrade the FMC to version 7.4 and assign the policies to new FTD running version 7.4 ???? Thanks
Resolved! Question on FTD Mgmt & Diag Interfaces
I'm currently following the guide listed down below in order to deploy some FTDs in Azure which I've been able to (still in early stages). However, looking at the guide and referencing other materials online, I always see the Diagnostic0/0 interface ...
Hello Cisco Community,I am a senior networking student currently planning my graduation project. I’m looking for a unique and innovative idea that combines networking, security, and, if possible, some programming aspects.If anyone has idea suggestion...
Problem Details: Configured 2 Destination NAT as per below nat (Inside,Outside) source static 10.8.55.229 199.19.3.64 unidirectionalnat (Inside,Outside) source static 10.8.55.229 199.19.5.67 unidirectional Following plan below configured above 2 line...
Resolved! Firepower syslog retention period
If anyone knows about the syslog retention period on the Firepower itself, could you let me know?I am using the Firepower 3100 series. The Firepower is acting as an ASA on the appliance. I use OS 9.20 (3).Syslog information is basically set to be tra...
i try https://firepower_mgmt_ip ,and get service unavailable.how to disable https for firepower?
Hi Cisco Community, I have a Cisco FMC and two Cisco Firepower devices. I would like to back up all system configurations on the FMC, including objects, NAT rules, ACP rules, and all other settings except for license and smart license information. I ...
Hi,I already have configure the ldap and it is working on VPN perfectly, but when I configure LDAPs i'm getting login error with the following error on the logs:"AAA unable to complete the request error reason memory error"I have done the following:T...
Hi all,So we have an issue on one of our networks that we are trying make work. This is in relation to a request for a basic NAT set up for RDP.Scenario is as follows:-A server sitting in AWS environment needs to access a server on a DMZ hanging off ...
I'm looking to get some basic reporting from FMC for things like top talkers but can't seem to do it in FMC because a lot of the logs are not going to the event viewer due to its limited size. What is a simple tool that can be integrated to get repo...
Hello,We have an ASA 5545 (9.6) with firepower services and FMC ver 6.4.0.9. When checking the connection events, I noticed that the 'URL' and 'URL Category' fields appear in some cases, but in other cases they appear empty.This produces erratic beha...
Hi all,As the title says, I'm trying to upload an upgrade file (Cisco_FTD_SSP_FP1K_Upgrade-7.6.0-113.sh.REL.tar) for my FTD to FMC. For some reason when I select the file and click upload the browser behaves as expected. However, after a minute the u...
Hi Team, We have old Cisco ASA need to confirm that config and sessions are synced to the Passive ASA????? This host: Secondary - ActiveActive time: 30555250 (sec)slot 0: ASA5515 hw/sw rev (1.0/8.6(1)2) status (Up Sys)Interface INSIDE (10.30.136.10):...
