hi, Am working on a Firepower 2110 device and we have installed ASA 9.8.2 image in it. We are not able to toggle between FXOS and ASA. From FXOS console there is no option connect asa, there is only connect local_mgmt. Could you please let us...
Forum Posts
Hi Everyone 1. nat (inside,any) source static INSIDE INSIDE destination static SITE1 SITE12. nat (inside,twbc) source static INSIDE INSIDE destination static SITE2 SITE23. nat (inside,twbc) source static INSIDE INSIDE destination static SITE3 SITE34....
Hi everyone Im upgrading the firewall hardware. I saved the identity certificates from the old firewall and then I took a screenshot of the ASDM which has the identity certificate information. I then realised that one of the certificates has mor...
Hi guys, I need a information about asa with firepower. One customer has a two asa and two firepower works in a different location . they want to do HA. İs that possible do that. Or What is the possible option to do ha for example 2 asa ha with o...
Does anyone have any suggestions for 3rd party feeds that your FMC could subscribe to or creating my own feed that we could subscribe to? For example, we got hit with a phishing scam and the URL wasn't blocked by the default feeds the FMC subscribe...
Hi. I have a 5545 FTD HA pair and I want to know if is possible to use the IP on the outside interface for the primary device to configure a AutoNAT. The primary device has the IP Outside 200.200.200.1 255.255.255.240 the secondary standby device...
hi dears please i have problem to access my web server from outside my scenario it is have multiple network subnet like in the diagram and i enable the routing between all please can you support me to fixing my problem
Hi to all, I am configuring the SNMP on a Cisco 5545-X FTD 6.3.2 for the first time via FCM.The SNMP configuration is ok, I receive the trap on my NMS server (Link/Up, Link/Down etc.). Now I want to monitor ASA5545 health status and in particular I...
Hello Experts,I have cisco 1941 on site A and Cisco asa 5500 on the Site B. I have created IPSec tunnel within. I want to Allow few host & ports from Site A to SIte B and vice versa. On Site A we have 5 IPs :-1. 10.10.10.12.10.10.10.23.10.10.10.1694....
Hello While researching and developing automation around the firepower REST API there seem to be a problem creating Access Policies that inherits another policy. When creating a policy (POST to https://{fmc_IP_or_name}:{https_port}/api/fmc_config...
Hi Folks, I am focusing on the accuracy of firepower applying appropriate IPS signatures based on Host definition. I've raised a couple of posts already online. However I'm still finding out from the server team what is definitely installed on the se...
Hi, I plan to upgrade sensor as below ( no downtime as current only monitor mode ) not comfortable to reimage. Current version FMC - 5.4.1.6sensor fw01 - 5.4.1 sensor fw02 - 5.4.1.5 phase 1 FMC : 5.4.1.6 > 5.4.1.10 Sensor: 5.4.1.0 > 5.4.1.5 > ...
I need to know what commands to use that will send any typed command to my SIEM. I am running the archive command on my switches successfully, but can't find a similar command for either my routers or firewalls. I am running current current IOS c...
Dear All Iam tried to access the FMC through web interface with the ip address of 192.168.45.5, we got the login page but we got the error (unauthorise to access) but through SSH i can able to login with default password. after we did restart the...
Hello, I was wondering, if it is possible to upgrade an existing FireSIGHT/POWER platform running on ASA 5545x to FirePOWER Threat Defense (FTD). Current software version of FireSIGHT and FirePOWER module are 6.2.0.5. Please advise. Thank you. ...
