Hello, Just wondering if anyone has the same issue as me. I have upgrade my 5545x from ASA w/Firepower Services to an FTD. I only have a BASE license for this unit, but I am unable to deploy any policies to it. There is a warning saying I need a...
Forum Posts
I tried to generate a custome report, but it fails all the time with "failed to generate" - where can I find more information about the failure reason? Other reports works without issues. Previews in the report template are also created successfull...
I want to check specific ports & protocol messages for their data and only allow that data between two interfaces when it matches any of the conditions. I built a regular expression class and have it OR match between the different regular expressio...
Resolved! FireSight Managment
We recently got a quote for a HA 5506 pair with Firepower and was surprised to see that it included a VM for the FireSight Management application. I have heard from a few people that the VM is not needed and we can run the management application on ...
Hi Support Community I was wondering if someone here can answer my question. I have a customer that has a Cisco 4140 Firepower Appliance and this is doing Data Centre segmentation. Does the Firepower Appliances support sending traffic out the same ...
Hi, I have a 5506-X that was running 9.6 with a simple setup that had a small external switch to bridge the inside, firepower, and our network together. I upgraded to 9.9(1) and wanted to make use of the new BVI feature and eliminate the external s...
Hi, I would like to configure authentication for our anyconnect connection using ldap to check the credentials against our AD. I can configure to use either sAMAccountName or userPrincipalName but not both at the same time. ldap-naming-attribute ...
Resolved! Port Fowarding on the ASA 5525
Hi, I'm currently migrating from a simple iptables Firewall to the Cisco ASA. I'm pretty much done, there's just one issue I'm having here. How do I setup port forwarding? I'm using ASDM but am also willing to use CLI if it helps the cause. ASA v9.2,...
Resolved! Cannot Disable Debug on ASA
I tried the following commands & although the output says its disabled I keep seeing it enabled when I enter "show debug". Also tried in config terminal mode & still could not delete the debug. Usually these commands will delete a debug. I'm confused...
First off Anyconnect works perfectly with 3 laptops my techs are using. They all have version 4.5 Anyconnect client apps & never have any issues. However one of my other users has Anyconnect client version 3.1.12020 & can successfully authenticate (...
Resolved! ssh access to Layer 3 specific interface
Hi I am just reviewing one of our L3 cisco router and I am seeing there are 4 different VLAN interfaces configured with IP addresses (wireless , Data , Video , Management ) when I do ssh to this switch from my desktop I am able to use any of these ...
I have a UCS environment on 3.1.1K firmware and I see that is TLS 1.2 capable (https://www.cisco.com/c/dam/en/us/solutions/collateral/enterprise/design-zone/ssl-tls-vulnerability-response.pdf) Is there any additional steps to make sure TLS 1.0 is d...
This topic is a chance to discuss more about all you need to know about Cisco FirePOWER security solution. On this session, Marvin Rhoads will be answering all kind of questions about FirePOWER Management Center (FMC), FirePOWER Threat Defense (FTD) ...
hi，all There is a problem in the VPN connection and authentication failure through the AD domain. The current problems are as follows:1, the terminal now dials VPN can pop out the authentication page;2. After the terminal submits the authentication...
Resolved! Recommended Firewall [Security] reading
Hello I was wondering what sort of path and direction to take on learning more about the security aspect of Cisco. I am getting acquainted with the ASA setup and then I see the NGFW (CX IPS?) and then FirePOWER (also part of the NGFW platform??)....
