With Prime 3.1 is it possible to setup an alarm that will notify you when a wireless client disconnects from the wireless network?
Forum Posts
Need some assistance with the new ASA-5506X for my home network. For some reason, i can no longer access the FirePower module via the ASDM. ASDM starts to load at stops at 17% (Initializing FirePOWER communication). Here is the error:Cannot connec...
Resolved! ASA with FIREPower Service and licensing
Hello,if I buy a ASA with FirePOWER Service (e.g. 5516-X) which licenses do I need to buy?As I understand I have to order a license for the FirePOWER Service. E.g. IPS, URL and AMP.Do I need to order a FireSIGHT Management license, too? Is the FireSI...
Resolved! unable to login in FWSM
Hi,I am having two dc switches with FWSM modules installed. DC switch1 FWSM (Ver 3.2(12) is wokring as active and Secondary DC switch2 FWSM (ver 3.2.(12) is in standby mode.From yesterday I am trying to login primary FWSM, It is accepting my use...
Hi all, I am trying to re image the firewall 5506-x with firepower services. Currently my firewall has this IOS insataaled: asa961-lfbff-k8.SPA. i configured it and it was working fine (No Firepower services yet). after approx one month of configurat...
Hello, Suppose we have two NAT rules under 'NAT Rules'; # Type Original (Source) Original (Destination) Interface (Translated) Address(Translated) 1 Exempt ANY ANY ...
Good evening - I'm receiving the following error when trying to remove wccp and reconfigure it: ERROR: Can't change redirect-acl, first remove wccp configuration and re-enter with new redirect-acl. I was running version 9.8(1), and I ran across a ver...
Hi, I need some clarification on the dependency of the firepower management console with regard to the sourcefire sensors. What is the expected behavior when the FMC is offline? Today we started experiencing failed connections and latency to an spe...
Hi guys, Consider the following topology: Let's say PC1 is my "management" device or network. - Both ASA's can reach eachother over the 2 different VLANS. - The ASA's each "represent" 1 datacenter. Now there is the following issue if i want to ...
Hello everyone, Im very new here and to this device, so excuse me for such a noob question.My manager told me to open on firewall ports for IP softphones, servers are located in cloud on the internet.internal addresses are any from local network.Outs...
Hello All, I have configured URL filtering to block certain pages. I have configured ssl decryption as well. But I noticed that when an https website is blocked firesight is not showing the block page. When http website is blocked the block page is ...
We have ASA with Firepower module managed by virtual FMC. I've noticed on FMC that application of access policy is still running for almost two weeks. Can you help me on how can I check thru CLI its progress or if there is a way that I can gracefu...
HI Team, We have two ASA 5525X and working with HA suddenly HA is not working . I have attached show tech support for both firewalls. As of now running with secondary firewall only suppose switch off/reboot the secondary firewall ,primary...
Sourcefire Questions: - How long do the events appear in the Intrusion-Events tab for you to be able to download the PCAP files? Is there a length of time these are visibile for or is there a limit on how many you can see/download? - Once you hav...
Resolved! No Failover Active command
Hi All, I have an active/standby pair of ASAs in transparent mode. 5515x running 9.1 (2). I have been trying to test failover by issuing the no failover active command on the primary. I thought that when I done this on the primary/active unit it woul...
