No ip connectivity between 2 private networks, each behind a cisco asa, with an ipsectunnel between them. The ipsectunnel is up, but no ip connectivity. I did configure the networks behind each site.One network try's to ping the other one without res...
Forum Posts
Hi Cisco Support, May we request for your assistance if our setup in branch router regarding zone base firewall? We convert our CBAC config to ZBF because we are using isr 4k routers. Our branch has 2 MPLS/IPVPN links 2 of each tunnels. We bind the z...
hi,i'm trying to clean up ASA NAT.using the show nat output, do i remove the ones that got both translate and untranslate 0 hits? translate_hits = 1305069, untranslate_hits = 0 <<< DON'T REMOVE? translate_hits = 0, untranslate_hits = 0 <<< REMOV...
I am getting the following errors in my identity policy - Is this error a warning that can be ignored? If not why can I not add multiple rules in my identity policy?
So I am in this dilema where the person before me configured our internet ASA using all ASDM, so its hard to figure out what is what in the CLI since all I see is DM_INLINE_blah. for example: access-list INSIDE_access_in line 15 extended permit objec...
Hi Guys, We have a challenge to restrict the Maximum no of LSA received on ASA 9.4 version (The number of OSPF LSA messages accepted by the device should be limited) We have a similar functionality on Routers with the help of the command (max-lsa max...
Resolved! ASA 5516 DATA PLANE STATUS DOWN
Dear ALL,I am installing ASA 5516 with Boot and Sys Image of 6.0.0-1005. After installing The SFR Image by DAta PLANE went to Down Status. i Perfromed Rebot of The module but still issue reamins the same. i Have Attached Cureent Screenshot of the ima...
Resolved! Port Forwarding ASA 8.6
Hi everyone! I have a problem with port frowarding to my IP camera from internet. My configuration looks good, but the port forwarding doesn't working from Internet. Config is below: Interface GigabitEthernet0/0.666vlan 666nameif IPCAMsecurity-level ...
I am trying to connect 2 VMWARE servers directly to my 5515-X firewall.And this is the configuration I am looking for:Gi0/0 - outside (already configured and working)Gi0/1 - inside (already configured and working)Gi0/2 - trunk with VLAN 1 + 2 + 3 + 4...
Hi allWe have a requirement to provide IPS services on a HA pair of 4100 series FTDs. Specifically there is one flow we need this for. Two clients (servers) need to talk to four servers. The end-to-end path is: Clients > FTD/IPS > F5 load balancer > ...
Resolved! Firepower 2K Highavailability
Hello everyone I am trying to deploy a pair of 2Ks with code version 6.2.2 in Highavailability mode. My wish was to use the Etherchannel subinterfaces to perform this task (to use as Failover links) but those don't appear under the possible interface...
I have the following question: can I configure two or more PBR policies in the same interface?
Hi guys, how can I reset GUI IPS password for ASA 5545? Thanks
New to ASA Firewall. Trying to setup a home lab following a Microsoft guide. I have one network that is using AT&T ARRIS NVG599 and I have my home lab network using a Dell server with VMWARE installed that has 2 NIC cards, one NIC card goes to the ...
Resolved! port forwarding help
I cannot reach internal web server 192.168.127.1 on port 443 from outside, on ASA 5506In fact I cannot reach 192.168.127.1 and 192.168.127.10 on any port from outside.ASA Version 9.7(1)4 ! hostname xx domain-name x.local enable password x names ip lo...
