Can someone help me out with this problem? We currently have 1 ASA in Datacenter 1 and are trying to implement a second firewall in another Datacenter. The interconnectivity between the Datacenters is fine, but i'm getting the "Failed to locate egres...
Gents, Is there any benefit of having the appliance operational considering it has old signatures that may still block some attacks?. The IPS device has no Cisco SmartNet contract and no signature releases supported by Cisco. Please advise,
I created a VPN tunnel from a Cisco 2911 to a sonicwall TZ series. The tunnel shows up and active on both ends but I cannot ping either side nor remote desktop etc. Not sure what I'm missing to allow traffic both directions. Any help as always is app...
Hello, im trying to register the FTD at FMC, both are in the same LANThe FMC has the IP 10.1.1.31The FTD has the IP 10.1.1.30 Im trying with the below command:> configure manager add 10.1.1.31 cisco123And im expecting to see the below outputManager s...
I have 2 ISP links that I want to set up SLA Monitor through FMC. I'm able to ping those two uplinks from my firewall. I setup SLA Monitor as shown in screenshot (attached) 2 ISP default routes screenshots are attached, as well. However, as soon as I...
Dears,We have RV042 Small business security Router, this router connected to ISP Modem (Bridge Mode) then to ISP.Interface WAN of this router configured with static real iP.We enabled https and we can reach router from outside.But when we try to esta...
Hello. Recently we installed a brand new ASA 5506 for a client. After the installation we were able to SSH into the device via the outside interface and the outside interface responded to pings. Now, the ASA will not respond and we cannot SSH to it. ...
I have ASA 5512x Base licence with Firepower i want to make upgrade of his licence and purchase a second ASA 5512x SEc-Plus without Firpeower to make a failover is that possible and how i configure it?thank you.
Dear all, Currently I have ASA 5512-x with ios 9.0.2. and I need to upgrade license to ASA firepower. Please help guide me, how to upgrade ASA 5512-x to ASA FirePower. Best Regard
Would you please help me on how to create a Layer 7 classmap/policy-map and specify an action of "allow-tls" using ASDM in ASA.I need to do this to allow the TLS traffic passing through the ASA from outside,
Hi, I've installed 2 software versions of the virtual management centre in our lab and the next step is to install eval licences. I need to get the UDI Product ID & UDI Serial Number but I'm not sure how to go about this. These are the files I have h...
I'm not (yet) an expert with Firewalls, but is there a reason why i can't ping subinterfaces from 1 ASA to another (or even from 1 subinterface on the ASA to another subinterface on the same ASA)? I can ping devices behind the subinterfaces, but i ju...
I created the following static NAT object network Internal_DNShost 10.154.2.12object network External_DNShost 10.1.250.5 nat (LAN,INSIDE) source static Internal_DNS External_DNS it is not working. What else am I missing?
I need to allow to connect to a internet web server using a public IP address. I added this to my ASA 5520. object network Polycom-10.154.10.5host 10.154.10.5object network Polycom-10.154.10.5nat (inside,outside) static 201.201.134.151access-list Out...
I recently had an issue where my FMC VM was virtually down due to the CPU being pegged at 100%. The GUI was inaccessible but I was able to login via SSH and issue a restart. After 30 mins the FMC had still not shutdown so I had to force it down wit...
