hi
i am trying to reset the password for admin user (for the web interface) for my firepower mgmt center with the following command
sudo usertool.pl -p 'admin Sourcefire'
but when i run it i see the following error message
Password length is 0 at...
Hi.
I am working my way through the 45-day eval of an ASA5506 Firepower IPS and have resolved most of the problems. One issue still remains:
Even though ">show time" displays correct time for both UTC and local, all syslog messages are stamped with ...
hi, i facing a PBR issue on ASA,
as i know , the normal PBR format is:
access-list to_ADSL extended permit ip 192.168.1.0 255.255.255.0 any
route-map my_map permit 100 match ip address to_ADSL set ip next-hop 100.0.0.1
then apply it on the interfac...
Hello,
I am in need to verify that I have configured our ipsec tunnel to be FIPS compliant. Here is a sample that I created to make sure I am good:
crypto ipsec ikev2 ipsec-proposal testing protocol esp encryption aes-256 aes-192 protocol esp integr...
Hi Team,
Can you please let me know, how to downgrade the Cisco FirePOWER 7020 sensor from 6.0.0 Build to 5.4.0.9 remotely.
Request to share the steps involved in downgrading remotely, as I don't have physical access to the device.
Thanks,
Murali ...
Hi,
Based on the attached screenshot on the report.
What is the root cause IP and destination IP for faceboook application ?
Can we find in the firesight analysis ?
Appreaciate it thank you
Dears ,
i want to know which privilege i suppose to use to allow certain user to do "sh version" command as i tried some privilege and they all do the same
as privilege 15
Hi All,
I have a problem since Friday and no shared support has not been renewed so I cannot open a TAC case.
We have found that the ASA 5525X on ver 9.4.3(8) just started to deny all DNS requests.
We have an ACL that allows the Internal DNS server...
I'm hoping someone can help here.
I have a Firepower Management center (virtual). Version 6.1
I'm getting a critical health monitor error
URL Filtering Download Failure.
all the procedures to troubleshoot on the web are for 5.4, and things don't l...
Does anyone know if wildcard certificates are supported for SSL decryption? I can install the wildcard certificate but into the FMC but when I use it in my SSL policy I receive certificate errors when going to HTTPS sites. The wildcard cert is signed...
friends
Goal: migrate a pix configuration from pix 515e number 1 to another pix 515e number 2
i have a pix 515e firewall
I have saved the configuration by
opening a hyper terminal session to the pix ( number 1 )
and capturing into a txt file a sh...
Hello all, i just had a few questions about Geofiltering on an ASA 5512-X with FirePOWER services managed through ASDM. I believe that I have the rules setup correctly as everything is functioning as it should. I have the rules setup so that any pac...
Hello
I have purchased cisco L-ASA5515-TAC-3Y license and activated. It must active protection, control and url filtering in my SFR. But when I added license to my FMC, Just url filtering activated. I rechecked my license key from Cisco License R...
Hello Guys,
I am using source firemodule ASA, I have dual ISP terminated on ASA.Source fire will be used for URL filtering, I need to use both ISP link, Please help me on dual static routing part in ASA.
Hi
I have an issue where I get complaints that the CISCO ASA 5505 that we have deployed around the country "closes ports" randomly. We have been trying to nail this not to precise error description reported to us for a while. We believe that it is r...
