hello I am trying to launch ASDM but it gives me error saying unable to launch device manager from x.x.x.x I am running it on VM on windows 7 , I have installed JRE . what could be the problem?
hello I am trying to launch ASDM but it gives me error saying unable to launch device manager from x.x.x.x I am running it on VM on windows 7 , I have installed JRE . what could be the problem?
Hello any one have a doc step by step ( first setup and configuration of asa) and Firepower ? thank you in a advance
I am running FireSight version 6.2, the FireSight take the time from NTP. We are in Egypt, we have the time changing each summer one hour to match the UTC time, but this summer the time has not been changed, hence I have the time is one hour after th...
We're looking at deploying 40+ Firepower ASA modules across our network (multiple sites) and I'm trying to find the best (read: fastest, least administrative) way to bring these modules up to 5.4.1.7 from 5.4.1.0 - base system image - to 5.4.1.7 whic...
Hi ! Please help me to configure for nat a server into internet ,the Subnet is laying in Internet router. The internet router has one primary address and two secondary IPs configured. I want to publish the server using secondary subnet of the inte...
Network discovery in Firethreat Defense does not recognizes the OS and version for F5 ltm devices that are load balancing, therefore it flags those divices as compromised. Just wanted to know how would you deal with those devices? would you exclude ...
I'm trying to look for an answer to what's the max ARP table size on a Cisco ASA 5555-X. Does anyone know how to find the answer? Is there a show command I can run or a spec sheet that shows the max ARP table size?
if i want to capture packets of IKE phase 1 using capture command , is this the right command capture match udp eq port 500 eq port 500 i found this in cisco document ikev1/ikev2 - Captures only Internet Key Exchange Version 1 (IKEv1) or IKEv2 ...
Hi Wonder if you can help me as you have been superb in the Past. I have an Cisco ASA 5585-X Firewall that i have migrated the config manually from 8.2.(5)9 to 8.4(6) ready to upgrade to the latest version . All NAT translations have all been rebu...
My manager has asked me to purchase a new FW, I was just about to buy the ASA 5585x and realised it is EOL all ready! So I'm going to go for the FirePower NGFW 9300 series, the question is, can I run the ASA image on it and will I get all of the same...
I know you should be able to upgrade a Cisco ASA in an HA pair with zero downtime. But, if the firewall is running bgp or ospf. Is the an outage during failover? Thanks
I have what must be a simple issue... Setup is per attached. I am unable to ping the FirePOWER address from anywhere (except from the physical ASA itself). My L3 Switch is the DG. Some details from the FP module ----------------------[ eth0 ]-----...
Dears please find the attached topology, Questions: Please correct me if i m wrong I m planning to create two context on the ASA and the traffic these 2 context will receive is from 172.20.1.0/24,, 2.0,,3.0,,,4.0 etc etc Both context inside interfac...
We are running an ASA 5585 connecting different switch infrastructures with trunk interfaces. On trunk ten2/0 we have vlan 200, 201 and 203 (for vtp domain xxx) On trunk ten2/1 we have vlan 204, 205 and 206 (for vtp domain yyy) Now I need to add vla...
Hi, I'm just checking here to see if anyone else is aware that in the latest release of Cisco Firepower Management Center there is not audit trail for changes to the access control policy. Now I consider the ability to log policy changes to be a re...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-13-2025 12:52 PM | ||
| 11-03-2025 09:48 AM | ||
| 10-30-2025 12:44 PM | ||
| 10-23-2025 07:14 AM | ||
| 09-26-2025 12:33 AM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 3 | |
| 2 | |
| 2 |