Running on a FP2130 with 9.18(4)34 but the same problem seems to occur on 9.18(4)40.I am trying to have a user belonging to multiple groups map to a single ldap attribute-map mapping the memberOf a group to IETF-Radius-Class for the group policy.The ...
Forum Posts
Trying to follow DISA SRGs, and one of the requirements is to enable FIPS mode on our 2140 FTDs, managed by FMC. I am new to these so was doing some searching online and it sounds like CC compliance is what needs to be enabled.Am I correct in saying ...
We currently have ASAv deployed in Azure - Size Standard DS3 v2 (4 vcpus, 14 GiB memory). We are using an ASAv30 licence which will soon expire and we are considering purchasing another ASAv5 licence. However, I wonder if ASAv5 is limited to fewer vC...
I have a new instance on a 3120 with an inline pair, configured on a transparent FTD. It is a direct replacement for our Firepower 7125 appliance. We have a failover pair of ASA5555-X, one currently runs through a 7125 with an inline pair in front (...
Can anyone tell me how to get the rsa key file and the csr out of the FMC using WinSCP. I've seen so many video that show people using WinSCP to log into the FMC and get the .key and .csr file but they don't go into how WinSCP should be setup to get ...
Resolved! OpenSSH regreSSHion vulnerability in FMC
Hello. Do anyone knows if vulnerability CVE-2024-6387 affects Cisco Secure Firewall Management Center (FMC) VIRTUAL? I've been looking into the security advisory (https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-...
I'm trying to set up MAC filtering for a dpc3941b.In the dpc3941b MAC filter settings what is the difference between "Allow All" and "Allow"?Also, are there two different MAC lists, one for Allow and one for Deny?
I am currently doing initialization for FTD, but it seems cannot detect disk0, and it keep rebooting and eventually stuck at rommon mode. any idea how to fix it?
Please help. I have an ASA 5506-x connected to a 3750 swich. I cant ping 8.8.8.8 or anything external from the switch. I cant ping the other vlan subnets either ( the ASA has the route back to these). However, I can ping 8.8.8.8 and tracert successfu...
We have a Firepower 2130 that has all it's NAT rules/policies as being imported from our old ASA 5525. The ASA is still in production for a different purpose. While I can see the NAT rules on the Firepower, I can't edit them unless it's done on the ...
Host-A can ping firepower from inside to outside in range (10.10.10.0/25) but not in range of (10.10.10.128/25). If wild card 'ip route' at core-switch is set to follow (10.10.10.10.128/25) then Host-A can ping all ip's in that range. But all ip's in...
FTD has a regular schedule in FMC, but it never backs up to the remote server as it is configured to do, it always backups to local var. FMC backup to remote server works fine. The TEST button when testing remote connection/server works fine. Initiat...
Hey Folks, I have FMC with 4 FTDs (7.2.8), I'm trying to run this command for example on the CLI <grep -i -E "KexAlgorithms|MACs|Ciphers" /etc/ssh/sshd_config> what I noticed, is that the Space key is not taken, and for any command that has space, th...
I've noticed in FMC that I can see traffic logged that traverses the FTD however traffic to the FTD is not logged. I am curious to see if someone is trying a port scan or something like that. So for example if my FTD interface is 192.168.0.1 and I ...
my FTD is not connected with FMC and is showing a pending state. checked on my FTD , the time was showing wrong and NTP server was also not Sync# show ntp NTP Overall Time-Sync Status: Ntp Config Failedplease help me removing my current NTP server a...
