Can i use ASA-5525X in transparent mode with following situations 1. Four interfaces in the same vlan (two inside, two outside) 2. Two interfaces in one subnet and another two interfaces in another subnet
Can i use ASA-5525X in transparent mode with following situations 1. Four interfaces in the same vlan (two inside, two outside) 2. Two interfaces in one subnet and another two interfaces in another subnet
I have a Firepower virtual management server that is managing about 12 devices. (2-5516s, 2-5508s, and the rest 5506s) I'd like to have an SSL policy so i can inspect https traffic, but I'm not sure if this is going to degrade system performance too...
Anyone know where I can find the ASA Protocol Header Definition Files (.PHDF)? Thanks Frank
I have a customer with a 5512-X in HA mode. They are making a few transitions and want to employ inter-datacenter clustering to maximize redundancy and mobility of applications. They want to buy a new 5512-X and put it in clustering mode, then migr...
Hi Team, On of our customer wants to implement two links of 10mb each and run BGP for load balancing and failover between two links, is it be supported in 5506 / 5516? Found the below references for failover but not for load balancing: ASA Border G...
We have a FireSight system with one version 5.4.0.5 Virtual Data Center and several ASA devices. We installed some User Agents to get user logon/logoff information from MS AD servers, and encountered 2 problems: 1) All User Agent servers (window serv...
Hi, I have 4 WAN connections directly connecting on my current firewall 5525-X. Recently, I have bought another 5525-X for Active/Standby HA deployment. The thing i am confused about is how should i configure those 4 WAN connections for my second f...
Hi all, Is there a way (without adding second cable between modem and asa!!) with Software 9.1.6 to setup a nat, that allows me to access the dsl modem´s webinterface? Setup: Internet<--->DSLModem<--->Cisco-ASA<--->LAN The DSL Modem has an given i...
I traceroute from this VLAN to 8.8.8.8 After ASA, i get * * * * * *. So i captured the packet. I do have these in place. class class-default set connection decrement-ttl user-statistics accounting access-list out_in extended permit icmp any any That...
I configured the ASA using the wizard. I accepted most of the defaults but similar errors below are appearing in the log Failed to locate egress interface for UDP I'm a novice and do not understand the statement As I'm using DHCP for the inside an...
Hello Team, We Recently purchased Cisco ASA 5516 fpwr Bundle.(ASA5516-FPWR-K8). 3DES/AES is disabled by default. i took the License Cisco asa 3DES/AES License from cisco website by providing Product Serial Number . But Not able to activate key. Does...
Hello, I recently purchased an ASA 5506x box, but I had problems connecting to the ASDM after running through the Startup Wizard. I found out that the cause was to do with Windows 10 and the solution was to upgrade the FirePower module. I went ahead...
Hi I have had some very good feedback from these forums so am hoping you can help me with a problem i haven't come across before. We are deploying a new 100Mbit DIA service into our Existing datacentre provided by BT to a pair of ASA 5545-X firewal...
Hi there was executive report template in the earlier version of Firesight 6.x that was suitable for management and executives especially in a case of POC, but I can\t find it in the later version, any info about that?
Hello, Could anyone provide a download link for 6.6.1164.x patch, which brings module to version 6.6.1164.1169 and resolves updates issue, thant requires SHA2. Thank you.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
10 | |
5 | |
5 | |
2 | |
1 |