Is this version Cisco Adaptive Security Appliance Software Version 9.6(1)5 is affected by Cisco Adaptive Security Appliance SNMP Remote Code Execution Vulnerability and Cisco Adaptive Security Appliance CLI Remote Code Execution Vulnerability
Is this version Cisco Adaptive Security Appliance Software Version 9.6(1)5 is affected by Cisco Adaptive Security Appliance SNMP Remote Code Execution Vulnerability and Cisco Adaptive Security Appliance CLI Remote Code Execution Vulnerability
Hi People, I have a quick question, I'm trying to migrate a config file from a ASA 5540 to a 5555X. The 5540 config is on version 9.1 and I'd like to migrate to 9.6 I've researched that it's a direct upgrade but are there any CLI changes from 9.6 t...
Hi everyone I have a problem that's driving me nuts trying to troubleshoot. Brand new install of Windows 7 Dell latitude. I'm connected to our domain, but cannot browse the Internet with exclamation icon and msg "No Internet Access." I can ping all...
Hi! I am trying to do what I thought would be a simple task.I need to open some specific ports for our new phones which use SIP. I am unable to open any port att all. When I use "Open ports check-tool" or any other online service, it just shows "clos...
I have downloaded v 2.2-18 of the Sourcefire User Agent to use with my FireSIGHT Management Center. I installed the agent on a Windows 2008 R2 server. When I try to open the agent to configure it the program crashes with the exception:Application: Co...
Hi, My company have a Cisco ISE infrastructure with 5 servers. About a month ago, someone have tried a backup and it hangs out I have tried a manual backup, restarted the ise application via cli but the message continues. I want to schedule a new ba...
Hello, I have the following scenario for which I need some clarifications if it's supported or not. I need to access the file repository where the unknown file disposition files are saved. with a third party system. This third party system supports N...
Hi Friends, In my ASA 8.4(7)30 HA setup, i do see standby failed when i run show failover in Primary FW (Active) as given below. Primary - Active FW # show failover This host: Primary - Active Other host: Secondary - Failed Secondary - Standby FW...
Hello everyone !! Our client is requesting to enable FQDN based ACL's (mostly because its easy to give a URL instead of multiple ip's for the same URL) but when i researched it looks like this feature has lot of shortcomings like i listed below , co...
Trying to allow traffic from external IPs into the network using certain ports. Requirements are, 555 TCP - Forward traffic to static private IP address (Transmitter) 2001 TCP - Forward traffic to static private IP address (Transmitter) 3000 UDP - ...
Hi, I am planning to install a FirePOWER software module to one Production ASA 5525-X. I have read the "Install and Configure a FirePOWER Services Module on an ASA Platform" guide but I am not sure will the any parts of the process interrupt ASA tra...
Hi, Fairly simple setup overall: There is a Traffic Profile with traffic pattern and deviations gathered over time from the DNS sever - graph/data can be seen; Correlation Rule is created for that Traffic Profile. Again - nothing fancy - looking fo...
I do not think this is a difference between using the default class class-map and creating an acl matching ip any any. Can someone correct me because all FP documentation says create class-map sfr. policy-map global_policy class class-default sfr fa...
Hello, is that possible to log any config changes to a Cisco ASA using Syslog ? if yes, please let me know what level and wat syslog messages shows ? I have enable informational level, but on my syslog-server nothing is displayed about any config...
Hi, Is there any way to only allow specific port for local network like only http,https and ftp and block all others? I tried to create a acl for inside interface with inc. traffic for these port but it blocks everything. I have attached screenshot...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 7 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |