Hi, We are implementing 2 ASA 5516-X firewalls dedicated to AnyConnect VPN services. To ensure we are always operational --(and in the event of a failure -- resilient), we want to implement Zones on the "outside" interfaces. Basically each ASA wil...
Hi all I hope someone can help, i have a ASA 5505 (9.2(4) firewall that setup as follows. 192.168.246.1/24(inside)---- ASA5505---- 192.168.248.10/23(outside). My syslog was working OK, with a few messages going to it every now and again, however t...
Hi, I just found out ASA5506 does not have the capability of layer 2 switching. I know the ASA5505 does. Which ASA appliances do have layer 2 switching? Does ASA5508 or ASA5516? Thanks,Kunal chopra
Hello Community, We currently employ 1 Cisco ASA 5525, we are looking to increasing our redundancy, with that said we are looking to adding a second ASA 5525 with the same hardware specs to allow for a proper failover process. The question i have ...
Is it possible to upgrade (add more) RAM on the AMP8150 appliance? If yes, can it be done in house? Or is the RAM specific to the appliance and needs to be ordered through Cisco?
Hello All, Im getting the below bus error for all my 2811 routers across other locations. Can someone assist me on this. Software being the latest version and cant blame on code again..System returned to ROM by bus error at PC 0x42F9E8F0, address 0xB...
Hello, I have enabled build in ASA IP aduit policy. However, is it possible I can exclude some IP behind to protect? Regards, Machi Ma
folks I'm patching an ASA5585 10Gb sfp interface to a HP 10Gb sfp port I have to use a hp 10Gb sfp transceiver on my ten gigabit port but its not coming upif I use a cisco1Gb sfp transceiver it all comes up so I'm assuming the ASA doesn't like the H...
Hi On the Cisco ASA firewall I'd like to disable TCP state inspection for intranet traffic that goes through a site2site IPsec VPN tunnel. From my understanding this can be done like that: access-list tcp_bypass extended permit tcp object-group Intra...
Hi everyone, I'm trying to find an answer on this before I go ahead and perform the upgrade. I've been asked to manually upgrade the signatures on our IPS devices as we were behind due to a Sensor Softward version issue. If I perform the upgrade of ...
I just got a new ISP and they have their Gateway versus our other ISP which is just basically a modem connected to our firewall. Well we got new Static IPs and i thought if i simply changed all my current static IPs to the new one the switch would be...
Have a pair of 5525s in active/standby setup. Standby node shows as failed. If I "reset failover" from the ASDM, it briefly changes to Standby Ready then in a few seconds flips back to "failed". The failover interface shows as Up. No recent updates ...
We have 2 ASAs setup in an active/standby configuration. The "Outside" interfaces on each ASA connects to a 1 of the 2 switches in the switch-stack as do the border routers - and this is for failover redundancy. ISPs-&-INTERNET | | R--...
Hello, I have configured Active/Standby on two 9.5 ASAs. Failover is working fine. I have tested with powering off the active and its brings up the standby as active. These failover works without 'standby' command on the outside/inside interfaces....
Hello! I am setting up a ASA in a new environment - well actually building out a new Datacenter for us to store our servers and equipment in. So far I have been running into issues and have been able to resolve (like setting up a NAT for internet tr...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 9 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |
