I need to know the recommended versions for the below Virtual defense center current version is 5.4.1.3 7120 sensor device current version is 5.4.0.4
I need to know the recommended versions for the below Virtual defense center current version is 5.4.1.3 7120 sensor device current version is 5.4.0.4
Hi everyone I'm looking for a way to monitor traffic by ip address from my FireSight, we have an ASA5516X with firepower services. Hope you can help me with this. Best regards
Hello team,As per the configuration guide , If your deployment includes an ASA5506-X, ASA5508-X, or ASA5516-X device, you can store a maximum of 2,000 authoritative users, regardless of your Firepower Management Center model. Firepower Management Cen...
Hello All, Is it require firepower management center (FS750-K9) to manage ASAfirepower(ASA5525-FPWR-K9) & L-ASA5525-TAC- (IPS&URL) , can we manage single FirePower through ASDM 7.3 or higher ..?
Hi, What is Out of band ? may i know the use of OOB and it's configuration process? Thanks Ashu
We would like to know what would be the default thresshold in yellow and red? or it is ok to disable the event retrieval?
Hi all I made the jump from 5.4.1 to 6.0.1 and so far no problems, rules and settings are nicely converted where needed. However the Context Explorer is now painfully slow. Some graphs appear right away but others can take three minutes or more to lo...
Hi all, I am using ASA 5525-X with firepower module. I met 2 new concepts when I upgrade software to my sfr module, That are system image and boot image. I would appreciate if someone can tell me what the difference between sfr system image and sfr...
Dear Experts, I want to establish a connection from remote site and right now they don't have firewall. we have to allow the traffic from our firewall. below please find the natting configuration. Also, I have attached the network diagram for your u...
Hi, We are implementing 2 ASA 5516-X firewalls dedicated to AnyConnect VPN services. To ensure we are always operational --(and in the event of a failure -- resilient), we want to implement Zones on the "outside" interfaces. Basically each ASA wil...
Hi all I hope someone can help, i have a ASA 5505 (9.2(4) firewall that setup as follows. 192.168.246.1/24(inside)---- ASA5505---- 192.168.248.10/23(outside). My syslog was working OK, with a few messages going to it every now and again, however toda...
Hi, I just found out ASA5506 does not have the capability of layer 2 switching. I know the ASA5505 does. Which ASA appliances do have layer 2 switching? Does ASA5508 or ASA5516? Thanks,Kunal chopra
Hello Community, We currently employ 1 Cisco ASA 5525, we are looking to increasing our redundancy, with that said we are looking to adding a second ASA 5525 with the same hardware specs to allow for a proper failover process. The question i have i...
Is it possible to upgrade (add more) RAM on the AMP8150 appliance? If yes, can it be done in house? Or is the RAM specific to the appliance and needs to be ordered through Cisco?
Hello All, Im getting the below bus error for all my 2811 routers across other locations. Can someone assist me on this. Software being the latest version and cant blame on code again..System returned to ROM by bus error at PC 0x42F9E8F0, address 0xB...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |