Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

I'm sure I already know the answer to this, but is it possible to manage or at least have alerts from Open Source Snort boxes roll into Defense Center?  We have quite a few Snort  boxes using ET PRO signatures and we thought it would be nice to repor...

Looking for some direction with a problem I am facing. Environment: ASA5550 8.2 3 interfaces: campus 10.0.0.0/24 branch1 10.0.1.0/24 vendor 192.168.1.0/24 The FW on the other side of our vendor interface only allows IP's in from our campus network....

c09371 by Frequent Visitor
  • 674 Views
  • 1 replies
  • 0 Helpful votes

I am having a issue to undertand the NATTING in ASA, below is the issue which i am having as of now. getting drop:- can you please go through it and let me know what can be the issue packet-tracer input outside tcp 166.77.235.144 2020 166.77.174....

akash.deep by Community Member
  • 565 Views
  • 1 replies
  • 0 Helpful votes

Hello, Here is what I am trying to acomplish and all of my searches are turning up empty which usually means I have my head wrapped around it the wrong way. Here is what I am envisioning:We currently have a ASA 5510, port 0 is connected to our ISP wi...

fatcatpro by Community Member
  • 711 Views
  • 3 replies
  • 0 Helpful votes

Hello, I'm going to replace ASA 5550 in active/standby failover configuration. I'm going to replace the primary unit. I moved the flash from the damaged one to the new one. Everityng was ok. Actually one thins is different, the I guess "new" one have...

Hi All, I am facing a problem in NAT. We have done below NAT. nat (IPLC-IN,OfficeNet-OUT)  source static obj-10.1.146.67 obj-59.160.46.182 object network obj-59.160.46.182 host 59.160.46.182 object network obj-10.1.146.67 host 10.1.146.67 but it is n...

Hello All, I have recently configured a 5506 with a firepower module.  When attempting to connect to the module via ASDM, I am getting the error "Cannot connect to ASA Firepower module. Check that it is correctly configured and on the network..."  I ...

jcopling1 by Community Member
  • 6493 Views
  • 12 replies
  • 5 Helpful votes

Hi, not sure this is the right forum but here goes..... We have 40 sites on an MPLS network that are connected to 2 central sites. The 2 central sites are directly connected via a 100mb ethernet connection and are about 100 miles apart. One of those ...

louis0001 by Level 6
  • 627 Views
  • 1 replies
  • 0 Helpful votes

Hello, I have 2 ASA-5585-X-SSP-20 and I have configured them in active/standby failove mode. but when primary active device going down secondary standby device act as Active and primary device as failed. But when primary devices coming UP still Seco...

prem.ce24 by Community Member
  • 1692 Views
  • 2 replies
  • 0 Helpful votes

hello I have ASA 5525 and i create on it access rule to permit ping from 172.16.10.10 to 172.16.20.10 im pinging 172.16.20.10 from 172.16.10.10 with -t  now i want to deny ping. i modified this access rule to deny ping. but ping wasnot interrupted au...

Review Cisco Networking for a $25 gift card