I have a Cisco ASA 5505 Firewall with version 8.0(3). I am trying to allow an external network SSH access into an internal host.I am seriously struggling with this seemingly easy scenario. For protection I will use fake IP's - but here is what I wan...
Hi Everyone.I want to generate a ssh key on Catalyst WS-C4507R+E but the commande "crypto key...." does not work.Is anything required for that?
Hi all,I'm looking for some clarification in reference to trunking on an ASA.I have an ASA 5512-X with two 3750-X's connected to the inside and outside interfaces and I need to trunk between them. I can set up sub-interfaces and configure the correct...
Hello friends,Since I manage many ASA devices at the company I work where, I would like to get a tool to perform periodic and automatic configuration backups. I am just interested about the ASA configuration, don´t care about other modules. Does anyb...
folks We have a ASA with 5 interfaces installed (1 for outside and 4 for inside), at the minute only outside interface has ACLs configured and all the inside interfaces dont have any rules on them at all. I have been asked to configure some ACLs for ...
All, I have a remote IPS 4345 giving me the following error: Error: Cannot communicate with mainApp (getVersion). Please contact your system administrator.Would you like to run cidDump?[no]:This always clears up after a hard reboot. This happens on a...
I have recently inherited a pair of ASA 5510's at 2 locations that I need to upgrade to 5515-X's (4 total). Is there a way to migrate these two quickly and easily or will I have to do it all by hand and enter in everything? I can hope that there is a...
Hi,I'm trying to identify who is the source of several 733100 messages in my syslogs on an ASA 5520. I have the following threat-detection configurations enabled: threat-detection basic-threatthreat-detection statisticsthreat-detection statistics tc...
Does anyone know if you can configure a hairpin NAT on a Cisco SA540? I can configure NAT for outside users to connect to my mail server. And my internal secured network users connect to the mail server via the internal IP address. But I have users o...
Hello all,we have a Little Problem with our Public Subnets on our main Cisco ASA 5510.Following Situation: We get 2 different Subnets provided on the same Ethernet Switch from our Provider.Just like:- Subnet 1 11.11.11.0/28- Subnet 2 22....
Hi Guys,I am trying to open all ports between two LANs (LAN1= Inside, LAN2= DMZ) on my ASA firewall ..attached is my running config. What commands can I include to achieve this? Thanks for your help ..Richard
Hello all,Device: ASA5525SW version: 9.2(3)The Release Notes for 9.2(x) states that the ASA now supports the cpmCPUTotal5minRev OID.The OID returns there values. What is the difference between .1, .2 and .3 below?$ snmpwalk -v 1 -c XXXX 10.10.10.10 1...
could i replace the asa with sourcefire NOT "FIrepower" , because i have asa 5520 as a current firewall and some one advice me to replace it with a "Sourcefire SF-3D8140 ", and if bought it, how could i use this with the current setup scenario If th...
Hi All, I have asa 5525 version 9.1(2)i want to allow the traffice from outsid to inside and inside to outside. Also attached a diagram.Thanks
Hi. this is doing my head in. We use a asa 5510 with code 7.2. I'm trying to setup access to two simple webpages from the Internet. And they don't work. Traffic comes in on 212.217.2.44 and is natted across to 172.16.16.5. Similarly traffic comes in ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM | ||
| 08-10-2026 08:58 AM |
| User | Count |
|---|---|
| 4 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
