Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

I have an ASA 5510, and recently we had to move our web site to an external provider. However, portions of the web site still remain here on site. From outside, the web site operates fine, with the portions being hosted here as well as at the provide...

dhall8436 by Community Member
  • 1089 Views
  • 3 replies
  • 0 Helpful votes

All, I am looking to see if host based internet rate limiting is possible on an ASA for internet (not intranet) traffic.  Here is what I am trying to accomplish:- allow a single user 512Kbps per flow with a burst ability of 1Mbps- only rate limit on ...

casanavep by Level 7
  • 633 Views
  • 1 replies
  • 0 Helpful votes

 I have a slight emergency that was dumped on me to be done this week.I have an ASA 5520 and need to setup a DMZ for one server. It need to communicate to one server on my inside network and to the internet over specific ports. I am not totally ignor...

rhauk0868 by Community Member
  • 749 Views
  • 2 replies
  • 0 Helpful votes

I have a Cisco 5520 with the ASA-SSM-10 IPS Module. I am running version 6.1(2)E3. I need a way to whitelist an IP Address from a Security Scanning vendor. The vendor is Control Scan and everytime they try to certify our site it fails because the IPS...

dblount by Community Member
  • 6395 Views
  • 3 replies
  • 0 Helpful votes

Hi All,I am in quite the predicament, my company offers a cloud based infrastructure for customers who buy our software from us. We have a pair of ASA 5525-X w/ IPS with multiple vLAN's for each customers (inside) and one vLAN for our outside interfa...

Jazz80813 by Community Member
  • 2988 Views
  • 8 replies
  • 0 Helpful votes

Hi, We're using port based ACL in our ASA firewalls for site to site VPNs, it was working fine. However, after upgrading one of the firewalls to 8.4, we started to have issues. We then changed it to IP based and it fixed the problem. Are port based c...

punchhab by Community Member
  • 1077 Views
  • 1 replies
  • 0 Helpful votes

I know I have to purchase a security plus license to get gigabit speed on the asa-5510. The problem is the system is fully configured and online and the ports I want to upgrade are not e0/0 & e0/1. Is there any reason to limit which ports can be upgr...

Please help and suggestion on below point.I'm configuring vlan 3 on port 3 on firewall but is not pingable although I connect directly to the port.My goal is from my PC 10.10.10.X can access internet through vlan3 10.10.10.250. Here is my Firewall co...

baryanto1978 by Community Member
  • 1082 Views
  • 5 replies
  • 0 Helpful votes

Hi guys, I just have a doubt that, if I configure the active and standby mac address in failover, does it will cause any downtime? As I planning to configure the active and standby mac addresses in failover during production time and not wish that it...

Chin by Level 2
  • 5698 Views
  • 8 replies
  • 0 Helpful votes

 Hi all ,  I have ASA 5515-X with SW, 6 GE Data, 1 GE Mgmt, AC"PID: ASA5515  Licensed features for this platform:Maximum Physical Interfaces       : Unlimited      perpetualMaximum VLANs                     : 100            perpetualInside Hosts     ...

startx001 by Level 4
  • 1703 Views
  • 5 replies
  • 0 Helpful votes

Hello, I have a webserver on the DMZ and I want to capture all source traffic going to it's public IP.  I have used the ASDM packet capture before, but can't seem to get this traffic to show up. My webserver is on (example) 80.170.156.86 (Outside) an...