Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

Hi,In order to do a flash upgrade on a 5510, is there any way to get the files from the existing flash onto the new flash before you replace existing flash? Is there an online procedure?Thanks.

lcaruso by Frequent Contributor
  • 309 Views
  • 2 replies
  • 0 Helpful votes

I can't seem to get internet access with my current config, not sure what is going on with it.  I have my cable modem connected to my ASA @ FE0/0My Wireless Router connected to ASA @ FE0/1             Wireless Network = 192.168.0.0/24        ASA Netw...

jwood1650 by Beginner
  • 11484 Views
  • 6 replies
  • 0 Helpful votes

I have a server behind an rv042 that i would like to block access to on one port from outside in.  I have configured the rule as follows:  priority = 1.  policy name<name>.  enable<checked>.  action = deny.  service <service to block>. source interfa...

mialbert by Beginner
  • 425 Views
  • 5 replies
  • 0 Helpful votes

Resolved! Default Rule Query

Hi All,This is more of a clarification request of my understanding than a support issue. A firewall is typically locked down using ACLs on the inside & outside interfaces, and there are various static NAT statements for servers that are reachable on ...

Hi,ASA is upgraded to 8.3(1), how can i configure to allows inside host to ping and traceroute to host at outside?I try to configured as old version but its not work.hostname ASA5505!interface Vlan1 nameif inside security-level 100 ip address 192.168...

Rojer-bkk by Beginner
  • 4967 Views
  • 5 replies
  • 0 Helpful votes

Hi everyoneHoping someone can clear this up for me, as it's working but I have no idea why.we have a nat exemption rule for 10.0.0.0/8 to w.x.y.zfollowed by some static nat rulesand thendynamic policy nat rule for 10.0.0.0/8 to w.x.y.z natting to IP ...

Am I missing something in my config to allow internet access?  192.168.0.1 ---> my wireless router plugged into 0/1Here is my current config:ASA Version 9.0(2)!hostname ciscoasaenable password DQucN59Njn0OjpJL encryptednames!interface Ethernet0/0 swi...

jwood1650 by Beginner
  • 400 Views
  • 7 replies
  • 0 Helpful votes

Hi Everyone,I removed FTP  from global service policy.I have no ACL that permits or deny FTP traffic.But my understanding was if we remove some inspect from global service policy it does not work.But i am still able to access FTP websites?Is this def...

mahesh18 by Frequent Contributor
  • 3170 Views
  • 5 replies
  • 0 Helpful votes

We are in the process of migrating to the ASA service modules on both our 6509E switches from our current FWSM. We have used the Cisco conversion tool and applied that to the service module. When viewing the context in ASDM we are unable to view the ...

Resolved! asa5505 dns issue

I have just set up my asa5505 and while in the sh run I have the following linesdhcpd address 192.168.2.200-192.168.2.231 insidedhcpd enable inside!dhcpd dns 68.94.156.1 interface outsideWhen a client connects to the device like:192.168.2.215 there i...

vgreenlee by Beginner
  • 400 Views
  • 6 replies
  • 0 Helpful votes