I am having soem difficulty getting documentation and setup procedures for the new ASA 5512-X (or X models in general) firewalls.I know the IPS sensor is a software-based one, but I'm not sure how much different the setup in than with a 5510 and IPS ...
Hi everyone,I have ASA 5520.I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Help me please.Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.22...
Hi,I have an ASA-5515X with onboard IPS. Is it possible to purchase a CSM module for Antivirus protection and have it running at the same time as the IPS?If so should I be concerned about too much traffic interrogation causing potential latency?Thank...
Hello Community.As i know VPN doenst work well with NAT and PATon 3rd Party Firewalls.We have two site every site has a single IP Adress in the Internet, every Site has a Vigor Draytek Firewall. The ASA's are direct behind the Vigor Drayteks. ...
Hello colleagues,Quick question. Is it possible to define logical interfaces (sub-interfaces) to different zones in a Zoned Based Firewall/router?For example. VLAN 2, 3 and 4 are logical interfaces on physical interface Gi0/0. But we want to restrict...
Hi All,I need to understand if ASA 5550 ver 8.2(1) is comptible with IPv6, if not what is the upgrade path to make it IPv6 compatible. The requirement is dual stack of IPv4 and IPv6 should run in the same HA cluster and later will shift IPv6 complete...
ZyXel DSL modem (10MB download and 768Kbps or so upload)DSL modem is operating in bridge modeCisco ASA 5505 in routed mode with ten users behind the ASA. Nothing fancy about the ASA setup.Each user relies on their own FirePass or Cisco VPN client (o...
......
hi all,i'm trying to setup my 5505 for SSH but it seem doesn't work. console and HTTPS/ASDM are working.my teraterm is just stuck with the user/password screen. also tried using putty but still failed.ciscoasa# exitLogoffUsername: adminPassword: ****...
Hi,We are using MS System Center Operations Manager to monitor network devices. We are trying to monitor our Cisco ASA 5525-X firewall interfaces.We have a generic management pack installed that seems to work for parts of the 5525. We can see perf...
I have a client that has two remote sites connected over S2S VPN's. Everything works fine across these connections except for when they try to remotely connect to a PC using SCCM. The connection is initiated using RPC (port 135), however, they cann...
here is my config, i dont know what is wrong.Well its in this line but do i have to type in a ip even if comcast is giving me a dhcp address?route outside 0.0.0.0 0.0.0.0 any 1=============================hostname asa1domain-name mydomain.comenable p...
Hello,What is the best way to monitor historical stats on the # of conenctions on a ASA??I have Solarwinds setup but I am not seeing any usuable data (screenshot). Some other users seem to have had success using Solarwinds for this purpose. Is there ...
hi,I have Pix firewall 515e on inside interface its has configured with IP 192.168.0.254.And Global Nating is configured.global (outside) 1 interfacenat (inside) 1 192.168.0.0 255.255.255.0 0 0I want i configured Global nating only for only specific ...
Hi,I've been tasked with upgrading a PIX running v6.4 to an ASA5515X running v9.0...I've done a few previous upgrades manually (rewrite the entire config) and all good but there is a piece of static NAT that has me confused.How should the following l...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
