We have began implementing site to site VPNs using our FirePower Management center. I'm wanting to find a way to add the connections to the dashboard so that we can which VPNs are up and the traffic flowing through them quickly. We've created a dashb...
Forum Posts
Hi Guys, Does ASA 5585 support dual mode? I'm planning to install 2x 5585-X SSP-10 in a single chassis?Both SSPs are running the below version: Cisco ASA Version: 9.8(4)Firepower OS: 2.2(2.119)Device Manager Ver: 6.4.(9) I'm trying to run these 2 SS...
Hello all. My company has been using Cisco ASA in the datacenter for years and I'm pretty comfortable with them. We recently replaced them with Firepower 2100's as our ASAs went end of life and we were sold on the added benefit of FTD. Since insta...
Hello to the entire community, sorry if the query is too strange, but the truth is I have not been able to find official documentation that explicitly states, if when updating a Cisco Firepower Theat Defense model 2130, the version within its ASA sof...
Hi GuysI have a couple of questions.1.When adding an FMC to cdFMC (CDO), what are the minimum commands need to do on the firewall? how would I assign the IP to the firewall first?2.The second question is around the prefilter, If I create a prefilter ...
Hello guysI configured DHCP snooping on SW1.#ip dhcp snooping#ip dhcp snooping vlan 1#interface fast0/0 #ip dhcp snooping trust#no shutdown My endpoint is connected to interface fast0/1, Now my endpoint PC taking APIPA.Before snooping i tested...
Hello Guys,I have configured DHCP snooping on cisco switch and configured two DHCP scope on R1 and R2 to test the DHCP snooping functionality. Config output from the switch #ip dhcp snooping #ip dhcp snooping vlan 1#interface range fast 0/2-3#ip dhcp...
I have enjoyed a pair of Cisco firewalls on my platform for a number of years.The past 2 years have been hell though!The latest incident saw my complete environment being unavailable for 8 hours.My provider told me that this was not their fault but r...
Resolved! ASA FPWR 1150 - Ping dropped
HejI am new to ASA and having ping. When I do a packet tracer I see action is to drop.I am trying to figure out what I am missing. Regards fw01# packet-tracer input SERVICE-8 icmp 172.16.8.3 0 8 172.16.8.1 Result: input-interface: SERVICE-8 input-st...
One SME is hardware and other is virtual, will it support failover?Flow collector is physical and other is virtual, will failover support?
So, I just we to perform an update from 9.9.2.85 to 9.16.4 (last one) and it went fine. I was able to VPN in afterwards. However, the L2L tunnels went to MMG2 and would not come back up. I changed the boot order back to .85 and everything went bac...
Hi dears,How to factory rest the sfr module
Hi Dears,how to change the int BVI1 to int g1/2 on sfr. I have factory rest the ASA without factory rest the sfr, after config the ASA and removed the bridge group 1 and interface BVI1, and the int g1/2 is the inside interface. that is not ping-able ...
Resolved! FMCV Licsense and suport renewal
Currently we are using FMCV to manage 2 FP-7120. Now the renewal time appoarching. But i did not get information about the part number for FMC license and support renewal . Is FMC is Subscription or Perpetual. if it is Subscriptional any one can h...
Hi,Cisco Firepower 1120 NGFWFXOS: 2.10(1.75)FTD: 7.0.1-84Managed by FDM onlyI cannot access FDM web interface or SSH on the physical management1/1 interface. I can only manage it through the data interfaces which is fine but I want to setup up HA a...
